handi quilter Sixteen C-Pod Manual Download

Page: 1 / 11

HQ Sixteen C-Pod and P-Pod V.5 Upgrade Kit

| 1

HQ Sixteen® C-Pod and P-Pod V. 5

Upgrade Kit

February 2017

Table of Contents

Overview ........................................................................................................................................ 1

Kit Contents .................................................................................................................................... 1

Tools Required ................................................................................................................................ 2

Safety Precautions .......................................................................................................................... 2

V3 Encoder Upgrades ..................................................................................................................... 3

C-Pod and P-Pod Upgrades ............................................................................................................. 5

Instructions for Installing the Rainbow Motor Cable, QM20964 (If needed)..................................8

New Features .................................................................................................................................. 9

Troubleshooting ............................................................................................................................ 10

Overview

This upgrade to the HQ Sixteen C-Pod and P-Pod adds Precision stitch regulation capabilities. You must replace

both the C-Pod and P-Pod units. In addition, if your HQ Sixteen has the V3 Encoder, you will also need to

replace the X and Y encoders’ circuit boards.

IMPORTANT BEFORE PROCEEDING: If your machine has a buffer between the motor and the P-Pod

it must be removed first. It is not compatible with the new C-Pod/P-Pod kit. See the “Instructions for

Installing the Rainbow Motor Cable, QM20964” page 8 for how to identify if this step will be needed.

If needed, the rainbow cable will need to be ordered, because it is not included with the pod upgrade

kit; order number is QM20964.

Kit Contents (part number QM59111)

C-Pod, with board version 5 and software version 1.79

Part number QM59110

pictured on page 5

P-Pod, with board version 5

Part number QM59109

pictured on page 7

www.SewingSupplyWarehouse.com

Summary of Contents for Sixteen C-Pod












Search results

Summary of Contents for Sixteen C-Pod

Reviews:

Related manuals for Sixteen C-Pod

Brands by name

Popular brands

handi quilter Sixteen C-Pod, Manual

Search results

Summary of Contents for Sixteen C-Pod

Reviews:

Related manuals for Sixteen C-Pod

Brands by name

Popular brands