background image

WARRANTY

This HANDLER product is warranted to be free from defects in material and workmanship, 
when used under the conditions recommended by the manufacturer, and/or the purpose for 
which the product was intended, for a period of 12 months from the date of shipment from 
factory to job site of original owner. Products purchased from distributor warehouse stock 
are warranted for a period of 18 months from date of shipment from the manufacturer’s 
warehouse.

In all cases, the full name and address of the distributor must be supplied, along with the 
name of the customer, product name and number, and serial number. A copy of the original 
invoice, showing date of purchase must accompany the warranty repair request.

This warranty will apply to equipment installed, operated and maintained in accordance 
with HANDLER procedures and recommendations.

During the life of this warranty, HANDLER will repair or replace (At HANDLER’s option) 
free of charge. F.O.B. its plant, any defective part or assembly, if such defect occurred in 
normal service and was not due to apparent misuse, abuse, or accident.

Any warranty service performed in the field must be authorized by HANDLER MFG.  
Unauthorized service voids the warranty and any resulting charge will not be paid by  
HANDLER MFG.

HANDLER MFG. makes no other warranties or guarantees, expressed or implied. 
The merchantability of the components is expressly excluded. The manufacturer assumes 
no liability for indirect or consequential damages. 

Detach or copy and mail back to the address below. 

-------------------------------------------------------------------------------------------------------------------------

Customer Name:

Address:

City:

State:

Zip:

Model No.:

Serial No.:

Distributor:

Distributor’s Address

Return to HANDLER

HANDLER MFG.

612 NORTH AVENUE EAST, PO BOX 520

WESTFIELD, NEW JERSEY 07090-0520

Summary of Contents for 26A RED WING













Reviews: