background image

Warranty

Your Mud Butler fenders come with a 1-year warranty from the date of purchase. 

Warranty issues will be determined by and remedied directly through Handsome Cycles. 

Original receipt with purchase date is required to process your warranty replacement. 

Defective parts will be replaced immediately after review by Handsome Cycles. 

Contact 

info@handsomecycles.com

 with photo and description of your warranty claim 

along with a copy of the original receipt, and your full contact info, to start the process.

Returns & Exchanges

In the event that your Mud Butler fenders need to be returned or exchanged, please 

refer to the return and exchange policies of the vendor you purchased them from.

Handsome Cycles accepts returns or exchanges on all direct purchases within 30 days. 

Product must be in unused, like-new condition, with all parts and packaging, to be 

considered for a full refund or an even exchange. Repackaging or parts replacement 

fees will be applied to damaged or incomplete fender sets. Handsome will pay the 

shipping cost of returns and exchanges on shipments originating within the United 

States. International customers are required to arrange for and pay return shipping.

1620 Central Ave. NE, Ste.157,  Minneapolis, MN 55413

(612) 353-4035  |  info@handsomecycles.com

Summary of Contents for Mud Butler Fender




















Reviews: