3
Hangar 9 Toledo Special Assembly Manual
Included Parts Listing
Fuselage
(1)
Right wing with control horn
(1)
Left wing with control horn
(1)
Horizontal stabilizer with control horn
(1)
Vertical fin with control horn
(1)
Cowl with clear cowl template
(1)
Aluminum landing gear
(1)
Wheel pants (left and right)
(2)
Front windshield
(1)
Center window set
(2)
Front window set (right and left)
(2)
Rear window set (right and left)
(2)
16
3
/
8
x 5/8-inch anodized aluminum wing tube
(1)
5 x 1/4-inch andozed aluminum anti-rotation tube (1)
FuSELAgE
4-40 x 3/8-inch socket head cap screw
(3)
#4 flat fender washer
(3)
Nylon clevis
(1)
Pushrod keeper
(1)
Clevis retainer
(1)
Plywood throttle pushrod support
(2)
MoToR MounT
Small nylon motor mount
(2)
48mm EP standoff
(4)
8-32 x 2
1
/
4
-inch machine screw (EP)
(4)
8-32 x 3/4-inch machine screw
(4)
8-32 x 1-inch machine screw
(4)
8-32 nylon lock nut
(4)
#8 flat washer
(8)
WIng
20mm x 15mm x 8mm hardwood block
(4)
#4 x 1/2-inch self-tapping washer head screw
(8)
Nylon 1/4-20 x 1
1
/
2
-inch nylon wing bolt
(2)
Nylon clevis
(2)
Clevis retainer
(2)
Pushrod keeper
(2)
Wing bolt plate
(1)
RuddER
Nylon clevis
(1)
Clevis retainer
(1)
Pushrod keeper
(1)
PuShRodS
2
7
/
8
-inch pushrod (aileron)
(2)
25
1
/
2
-inch pushrod (elevator)
(1)
26-inch pushrod (rudder)
(1)
16
1
/
2
-inch pushrod (throttle)
(1)
12-inch nylon pushrod housing (throttle)
(1)
LAndIng gEAR
5/32 x 1
3
/
8
-inch axle with nut
(2)
5/32 wheel collar
(4)
3mm x 5mm machine screw (for wheel collar)
(4)
4-40 x 3/8-inch socket head cap screw
(2)
8-32 x 3/4-inch machine screw
(3)
#4 flat washer
(2)
#8 flat washer
(3)
2
3
/
4
-inch rubber wheels
(2)
CoWL
2
1
/
4
-inch nylon spinner, blue
(1)
#4 sheet metal screw (spinner screw)
(2)
4-40 x 1/2-inch socket head cap screw
(4)
#4 washer
(4)
1/4-inch (6mm) fuel tubing
(4)
ELEvAToR
4-40 nylon lock nut
(2)
#4 flat fender washer
(2)
Nylon clevis
(1)
Clevis retainer
(1)
Pushrod keeper
(1)
MISCELLAnEouS
EP plywood battery tray
(1)
Fuel tank assembly, 11 oz
(1)
Nylon tie-wrap
(2)
Velcro strap
(2)
1.5mm hex wrench
(1)
using the Manual
This manual is divided into sections to help make assembly
easier to understand, and to provide breaks between each
major section. In addition, check boxes have been placed
next to each step to keep track of each step completed.
Steps with a single box (
) are performed once, while steps
with two boxes (
) indicate that the step will require
repeating, such as for a right or left wing panel, two servos,
etc. Remember to take your time and follow the directions.
ultraCote® Covering Colors
• Cream
HANU878
• Sky Blue
HANU875
Before Starting Assembly
Before beginning the assembly of your model, remove
each part from its bag for inspection. Closely inspect the
fuselage, wing panels, rudder and stabilizer for damage. If
you find any damaged or missing parts, contact the place of
purchase.
If you find any wrinkles in the covering, use a heat gun or
covering iron to remove them. Use caution while working
around areas where the colors overlap to prevent separating
the colors.
HAN100 – Heat Gun
HAN150 – Covering Glove
HAN101 – Sealing Iron
HAN141 – Sealing Iron Sock
