background image

3

When your greenhouse need cleaning, use a mild detergent solution and risen with cool clean water.

Note that the door is hinged on the right hand side and therefore opens to the right side.

Hot items such as recently used grills, blowtorches must not be stores in the

Dispose of all plastic bags safely. Keep them out of reach of small children.

Do NOT use acetone, abrasive cleaners or other special detergent to clean the panels.

This is a multi-part assembly and needs at least 3-4 hours for assembly.

!

     SAFETY ADVICE

We strongly recommend the use of work gloves during assembly.
Do not attempt to assemble the greenhouse in windy or wet conditions,
Do not touch overhead power cables with the aluminum profiles.

Always wear shoes and safety goggles when working with extruded aluminum.

The greenhouse must be positioned and fixed on a flat level surface.

Do not lean against or push the greenhouse during construction.

Keep children away from the assemble area.

Do not position your greenhouse in an area exposed to excessive wind.

Do not attempt to assemble this greenhouse if you are tired ,have taken drugs or

alcohol or if you are prone to dizzy spells.

If using a step ladder or power tools ensure that you follow the manufactures safety
advice.

greenhouse.

Ensure there are no hidden pipes or cables in the ground before inserting the pegs.

    GENERAL ADVICE

Selecting a site-choose a sunny level position away from overhanging trees.

If you are fixing your greenhouse directly to a solid concrete foundation use the pre

drilled holes in the metal base supplied.

The component parts  should be checked and laid out close at hand.

Keep all small parts (screws etc)in a bowl so they do not get lost.

Keep roof clear of snow and leaves.

  

CARE & MAINTENANCE

  

Summary of Contents for 9820102-1























Reviews: