background image

 

3

IMPORTANT SAFETY INFORMATION 

 

The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas 
Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, 
CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. 
 
The appliance and its appliance main gas valve must be disconnected from the gas supply piping system 
during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa). 
 
The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve 
during any pressure testing of the gas supply system at test pressure equal to or less than 1/2 psi (3.5kPa). 
 
The appliance area must be kept clear and free from combustible materials, gasoline and other flammable 
vapors and liquids.   
 
Do not use this appliance if any part has been under water. Immediately call a qualified service technician to 
inspect the appliance and to replace any part of the control system and any gas control which has been under 
water. 
 

Children and adults should be alerted to the hazards of high surface temperatures and kept at a safe 
distance to avoid burns or clothing ignition. 
 
Young children should be carefully supervised when they are anywhere near the appliance.   
 
Clothing or other flammable material should not be hung from the appliance, or placed on or near the 
appliance. 
 
Any screen or guard removed for servicing an appliance must be replaced prior to operating the 
appliance. 
 
Installation and repair should be done by a qualified service person. The appliance should be 
inspected before use and at least annually by a professional service person. More frequent cleaning 
may be required as necessary. It is imperative that the control compartments, burners and circulating 
air passageways of the appliance be kept clean. 

 
Do NOT burn solid fuels in this gas fireplace. 
 
Do NOT ignite the burner before pouring all of the burner media (lava rock or fire ice) into the burner pan. The 
media must be evenly distributed over the burner. 
 
During initial firing of firepit, please stay away from the firepit for 20 minutes as fire media (lava rock or fire ice) 
may pop and hit someone on the face or eyes 
 
Do NOT ignite or use the firepit if the burner media (lava rock or fire ice) are wet. Ensure the burner media are 
completely dry before igniting as intense heat could cause the media to crack and pop. 
 
It is UNSAFE to use this product for cooking! 
 

CAUTION

: The propane gas pressure regulator provided with this appliance must be used. This regulator is 

set for an outlet pressure of 11 inches water column. 
 
This outdoor gas appliance is not intended to be installed in or on recreational vehicles and/or boats. 
 
Before each use of this gas appliance, open the LP (Liquid Propane) Tank Drawer and inspect the LP Hose. If 
there is evidence of excessive abrasion or wear, or the hose is cut, it must be replaced prior to the gas 
appliance being put into operation. Use only the replacement hose assembly specified in this manual. Inspect 
the burner before each use of the appliance. The burner must be replaced prior to the appliance being put 
into operation if it is evident that the burner is damaged. Use only the burner listed in these instructions.   
 
Keep the fuel supply hose away from any heated surfaces. 

Summary of Contents for Traditions TRAD5PCFPBR-RED


















Reviews: