4
English
Safety Notes
Wear personal protective equipment (PPE) (safety shoes, gloves, etc.)
Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the influence
of alcohol or drugs are prohibited from using this product.
Electrical connection
The current version of the applicable regulations from VDE, local authorities and
utility companies must be observed for electric installation work.
The installation and test work must be performed by an authorized electrician
under consideration of DIN VDE 0100 part 701 / IEC 60364-7-701.
The system must be protected via a leakage current protective device (RCD/ FI)
with a measurement difference current of ≤ 30 mA.
The proper function of this protective device must be checked at regular intervals.
The ambient temperature must not be higher than 50°C.
Installation Instructions
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the
applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• During installation of the product by qualified trained personnel, make sure that
the entire fastening surface is even and smooth (no protruding seams or tile
offset), that the finish of the wall is suitable to apply the product and has no weak
points.
• Any work may only be carried out in a de-energized state.
• Only standardized materials may be used for the installation.
• All components must remain accessible.
• No easily inflammable material is allowed in the immediate vicinity.
• The installation location of the iBox Hub must be accessible at any time and must
lie outside areas 0 and 1.
• The iBox Hub offers different connection options, LAN and HDMI, jack or Toslink
for AUX. If a screen is connected to the iBox Hub, the connection must be
established by means of a “fiber optic HDMI cable” or “HDMI glass fiber
cable”.
• The "hansgrohe installer app" is a mandatory requirement for setting up the iBox
Hub. This app can be accessed here: https://www.hansgrohe.com/smart-living/
app
• Hansgrohe SE hereby declares that the Pontos Base wireless unit type complies
with Directive 2014/53/EU. The full text of the EU Declaration of Conformity
can be accessed on the following website: pro.hansgrohe.com
transformer
The power supply unit must be installed in a flush socket > Ø 60 mm (deep
version). This flush socket is connected with the installation area for the iBox
control via an empty conduit EN 20.
The voltage supply from the 12 V DC SELV must only be fed via the included
transformer type 30335810. The transformer must be installed safe from outside
contact outside the zones 0, 1 and 2 in a flush-type box to be provided by the
customer.
The mains voltage of 100 - 240 V AC 50 - 60 Hz must be supplied via a shutoff
device (switch) as well as a ground fault protector (RCD / FI) with a measured
differential current of ≤ 30 mA.
For power supply, only use the power supply units comprised in the delivery. A
different or excessive use is considered non-intended. The user/operator bears
the sole risk. The intended use includes the adherence to the operating
instructions and the observance of the inspection and maintenance guidelines.
The manufacturer/seller of this product does not assume any responsibility for
injuries or damage that may be caused by improper installation or non-intended
use.
Technical Data
Type plate
see page 39
Interfaces
LAN RJ45
WLAN 2.4 GHz, WPA2 encoding
Bluetooth 4.1
USB 2.0 type A (debug interface)
HDMI type A
AUX (jack 3.5 mm / miniTOSLink)
CAN 1 (interface to the iBox Control)
CAN 2 (for future extensions)
transformer 30335810 (Technical Data see typeplate)
Input (IN)
100 - 240 V / 50 - 60 Hz
Output (OUT)
12 V DC SELV / 2,5 A
Dimensions
see page 39
weight:
92 g
LED-Display
• Green: System in operation
• Dark blue flashing: Search button active
• Light blue: Access point open
• Yellow: No MQTT connection
• White: Firmware update running
• Red: Fault
Repair
Only by Hansgrohe trained personnel or persons or companies appointed by
Hansgrohe.
Symbol description
Dimensions
(see page 39)
Installation example
(see page 37)
Flow diagram
(see page 38)
Spare parts
(see page 39)
Disposal of waste batteries and old Electrical &
Electronic Equipment
(applicable in the European Union
and other European countries with separate collection
systems).
This symbol on the battery, the product or the packaging indicates that the battery
or the product shall not be treated as household waste. By ensuring the battery or
product are disposed of correctly, you will help prevent potentially negative
consequences for the environment and human health. The recycling of the materials
will help to conserve natural resources. To ensure that the battery or product will be
treated properly, hand over the product at end-of-life to the applicable collection
point for the recycling of batteries, electrical and electronic equipment. For more
detailed information about recycling of this product or battery, please contact your
local Civic Office, your household waste disposal service or the shop where you
purchased the product.
i
Assembly
(see page 33)
