Safety Notes
Gloves should be worn during installation to prevent
crushing and cutting injuries.
Children as well as adults with physical, mental and/
or sensoric impairments must not use this shower
system without proper supervision. Persons under
the influence of alcohol or drugs are prohibited from
using this shower system.
The shower system may only be used for bathing,
hygienic and body cleansing purposes.
Do not allow the streams of the shower touch sensi-
tive body parts (such as your eyes). An adequate
distance must be kept between the shower and you.
The product may not be used as a holding handle. A
separate handle must be installed.
Shower hoses are only suitable for a connection
from the shower to the fitting. Never fit a shut-off
device between the fitting and the hose.
The hot and cold supplies must be of equal pres-
sures.
Installation Instructions
The fitting must be installed, flushed and tested after
the valid norms!
Optimal functioning is only guaranteed with the com-
bination of Hansgrohe hand showers and Hansgrohe
shower hoses.
Where the contractor mounts the product, he should
ensure that the entire area of the wall to which the
mounting plate is to be fitted, is flat (no projecting
joints or tiles sticking out), that the structure of the wall
is suitable for the installation of the product and has
no weak points. The enclosed screws and dowels are
only suitable for concrete. For another wall construc-
tions the manufacturer‘s indications of the dowel
manufacturer have to be taken into account.
•
•
•
English
The filter (94246000) must be insert to protect the
hand shower against incoming dirt by pipework.
Incoming dirt leads to defects or/and can damage
parts of the hand shower; such caused faults voids all
liability and guarantee claims. (see page 61)
Technical Data
Operating pressure:
max. 1 MPa
Recommended operating pressure:
0,1 – 0,5 MPa
Test pressure:
1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature:
max. 80 °C
Recommended hot water temp.:
65 °C
anti-pollution function
•
Dimensions
(see page 64)
Do not use silicone containing acetic acid!
Flow diagram
(see page 66)
Symbol description
Operation
(see page 67)
Safety Function
(see page 68)
The desired maximum temperature for exam-
ple max. 42º C can be pre-set thanks to the
safety function.
Adjustment
(see page 69)
After the installation, the output tempera-
ture of the thermostat must be checked. A
correction is necessary if the temperature
measured at the output differs from the
temperature set on the thermostat.
Assembly see page 60
6
Summary of Contents for Marin Thermostat Set 27097000
