background image

4

5

Deutsch

Deutsch

Die Montageanleitung enthält die wichtigsten 

Montageschritte  und  Installationshinweise  für 

die  auf  der  Titelseite  bezeichneten  Produkte. 

Lesen Sie die Montageanleitung aufmerksam, 

um Montagefehler zu vermeiden. Die Dampf-

dusche wurde nach den geltenden Richtlinien 

hergestellt. Unsachgemäße Montage kann zu 

Verletzungen führen!

Information

Die  Dampfdusche  wurde  konform  mit  den 

Niederspannungsrichtlinien 

73/23/EWG, 

93/68  EWG  und  der  Norm  CEI  64-8  (IEC 

364) hergestellt. Die Schutzart der Dampfdu-

sche  ist  IPX4,  die  Nennspannung  ist  230  V, 

die Nennleistung ist 2400 W für die Ausfüh-

rung Steam und Deluxe.

Die  von  der  "Europarichtlinie"  für  elektro-

magnetische  Verträglichkeit  auferlegten  Si-

cherheitsanforderungen  (Richtlinie  89/336/

EWG, 92/31/EWG, 93/68/EWG) und die 

Konformität  wird  durch  die  Anwendung  fol-

gender  europäischer  Normen  gewährleistet; 

EN 55014, EN 55104, EN 61000-3-2 und 

EN 61000-3-3.

Anschlussmaße

(Abb. B)

Position  1

:  Empfohlene  Stelle  für  den 

Austritt  der  elektrischen  Versorgung  aus  der 

Wand  (Kabel  3  x  1,5  mm2  /  Kabellänge 

2600 mm).

Position  2:

  Empfohlene  Stelle  für  den  Kalt-

wasseranschluss DN 15 1/2" Innengewinde 

für die Verbindung zum Thermostat.

Position  3:

  Empfohlene  Stelle  für  den 

Warmwasseranschluss DN 15 1/2" Innenge-

winde für die Verbindung zum Thermostat.

Position  4:

  Empfohlener  Bereich  für  den

Wasserablauf DN 50.

Hinweis:

Mindestraumhöhe von 2400 mm notwendig! 

Einbau  in  fertig  gefliestes  Bad  mit 

"Fliesenspiegel" auf mindestens 2300 

mm!

 

Erdungskabel:  Querschnitt  von  mindestens 

4 mm2 und einer Länge von ca. 2600 mm!

Vorwort/Anschlussmaße

English

English

These installation instructions contain the most 

important  installing  procedures  and  installa-

tion notes for the products stated on the front 

page.  Please  read  these  instructions  care-

fully  in  order  to  avoid  incorrect  installation. 

The  steam  shower  has  been  manufactured 

in  accordance  with  the  applicable  regula-

tions.  Any  improper  installation  may  lead  to 

injuries!

Information

The steam shower has been manufactured in 

compliance with the 73/23/EEC Low-Voltage 

Electrical  Equipment  Directive,  93/68  EEC 

Low-Voltage  Electrical  Equipment  Directive 

and  the  CEI  64-8  (IEC  364)  standard.  The 

steam shower's degree of protection is IPX4, 

its rated voltage is 230 V, its rated output for 

the Steam and Deluxe versions is 2400 W.

The  compliance  with  the  safety  requirements 

(89/336/EEC,  92/31/EEC,  93/68/EEC 

guidelines)  specified  by  the  "European 

Guideline"  for  electro-magnetic  compatibility 

is assured by the application of the following 

European standards; EN 55014, EN 55104, 

EN 61000-3-2 and EN 61000-3-3.

Connection dimensions

(Fig. B)

Position 1

: Recommended position for elec-

trical  supply  cable  exit  from  the  wall  (cable 

3 x 1.5 mm2 / cable length 2600 mm).

Position  2:

  Recommended  position  for 

cold  water  connection  DN  15  1/2"  internal 

thread for connection to the thermostat.

Position  3:

  Recommended  position  for 

warm water connection DN 15 1/2" internal 

thread for connection to the thermostat.

Position  4:

  Recommended  area  for  water 

drainage DN 50.

Note:

A  minimum  room  height  of  2400  mm  is 

required! 

Installation  into  completely 

tiled bathroom with a minimum "tiled 

area" of 2300 mm!

 

Earthing  cable:  Cross  section  of  at  least 

4 mm2 and a length of approx. 2600 mm!

Preface/Connection Dimensions

Italiano

Italiano

Le  istruzioni  di  montaggio  descrivono  le 

più  importanti  operazioni  di  montaggio  e 

le  avvertenze  di  installazione  per  i  prodotti 

indicati  nella  pagina  di  copertina.  Leggere 

attentamente  le  istruzioni  di  montaggio  per 

evitare  errori.  La  doccia  a  vapore  è  stata 

realizzata  conformemente  alle  direttive 

vigenti. Il montaggio scorretto può provocare 

lesioni!

Informazione

La  doccia  a  vapore  è  stata  realizzata 

conformemente  alla  direttiva  sulla  bassa 

tensione  73/23/CEE,  93/68  CEE  ed  alla 

norma  CEI  64-8  (IEC  364).  La  classe  di 

protezione  della  doccia  a  vapore  è  IPX4, 

la tensione nominale di 230 V e la potenza 

nominale  di  2400  W  per  i  modelli  Steam  e 

Deluxe.

I requisiti di sicurezza previsti dalla direttiva 

europea  sulla  compatibilità  elettromagnetica 

(direttiva  89/336/CEE,  92/31/CEE,  93/

68/CEE)  e  la  conformità  vengono  garantiti 

dall'applicazione  delle  seguenti  norme 

europee: EN 55014, EN 55104, EN 61000-

3-2 e EN 61000-3-3.

Quote di collegamento

(fig. B)

Posizione  1:

  punto  consigliato  per  la 

fuoriuscita del cavo di alimentazione elettrica 

dalla parete (cavo 3 x 1,5 mm2 / lunghezza 

2600 mm).

Posizione  2:

  punto  consigliato  per  il 

raccordo  dell'acqua  fredda  DN  15  1/2" 

con  filettatura  interna  per  il  collegamento  al 

termostatico.

Posizione  3:

  punto  consigliato  per  il 

raccordo  dell'acqua  calda  DN  15  1/2" 

con  filettatura  interna  per  il  collegamento  al 

termostatico.

Posizione  4:

  zona  consigliata  per  lo

scarico dell'acqua DN 50.

Avvertenza:

Altezza  minima  del  locale  2400  mm! 

Montaggio  in  stanza  da  bagno 

piastrellata  con  altezza  minima  della 

piastrellatura di 2300 mm!

 

Cavo 

di 

terra: 

sezione 

minima

4 mm2 e lunghezza di circa 2600 mm!

Introduzione/quote di collegamento

Summary of Contents for PHARO 21116000











































































Reviews: