background image

 

Hansa C27EU O&M Manual 

– OM-023 Revision A 16/10/19 

© Hansa Chippers 2019 

21 

 

Incidental  expenses  incurred  in  the  warranty  claim.  For  example:  additional  expenses  such  as  those  for  towing, 
communications, hotel and meals, incurred due to breakdown of the product at a remote location. Any expense related 
to personal injury and/or property damage, (exclusive of the product itself). Compensation for loss of time, commercial 
losses or rental costs of a substitute product during the period of adjustment.   

 

Any damage which results from unavoidable natural disasters, fire, collision, theft, etc.  

 

Any normal wear or deterioration, such as that of sliding or rotating parts caused under normal operating conditions. For 
example: Normal wear pivot points, rod ends and bearings.  

 

Any damage resulting from exposure of the product to soot and smoke, medicines and chemical agents, sea water, sea 
breeze, salt or other environmental phenomena. 

Limitations

 

 

HANSA reserves the right to modify, alter and improve any product without incurring any obligation to replace any product 
previously sold with such modification. 

 

In no event shall HANSA’s liability e

xceed the purchase price of the product. 

 

Equipment  and accessories not  of 

HANSA’s manufacture (such as engine,  battery and tires) are warranted only to the 

extent of the original manufacturer’s warranty and subject to their allowance to HANSA only if found

 to be defective by 

such manufacturer. 

 

HANSA reserves the right to supply remanufactured parts as it deems appropriate. 

HANSA Product Warranty Period

 

 

HANSA CHIPPERS 

DOMESTIC 

COMMERCIAL  
(EXCLUDING HIRE) 

COMMERCIAL (HIRE) 

Non-Registered                

12 months 

12 months 

 
3 months  

Extended Warranty  

36 months (Conditional)* 

36 months (Conditional)* 

 
N/A  

 

Each of the warranty periods stated above commence from the date on which you purchased your HANSA product. 

*Conditional Warranty: 

This is a HANSA extended warranty period for products that are: 

 

Purchased from an authorised HANSA Dealer. 

 

Registered at the time of sale through the Hansa Chippers website: www.hansachippers.com/registration 

 

Serviced by a HANSA Dealer in accordance with the Hansa service schedule using genuine HANSA parts. 

 

Meeting all other warranty requirements. 

Warranty  periods  vary  depending  on  whether  the  purchaser  is:  (i)  a  domestic  (i.e.  non-commercial)  customer;  (ii)  commercial 
customer (excluding plant/equipment hire businesses); or (iii) a commercial customer in the business of plant/equipment hire.   

General

 

1.

 

Your rights:  
a.

 

HANSA will recognise any implied rights and remedies that are available to you at law in the applicable territory and that 
cannot be excluded by HANSA.    

b.

 

In New Zealand, Hansa Products Ltd will recognise your statutory rights under the Consumers Guarantee Act 1993 (provided 
that you are a consumer for the purposes of that Act).   

c.

 

In  Australia,  this  warranty  is  given  by  Hansa  Products  Pty Ltd.  This  warranty  is  provided  in  addition  to  other  rights  and 
remedies you have under law - our HANSA products come with guarantees that cannot be excluded under the Australian 
Consumer Laws. 

2.

 

If any provision of this warranty document is held by any competent authority to be invalid or unenforceable in whole or in 
part, the validity of the other provisions of this warranty document and the remainder of the provisions in question will not be 
affected.  

3.

 

The English language version of this warranty document prevails over any translated version/s of its terms. 

4.

 

This warranty document is governed by the laws of New Zealand.  The parties submit to the exclusive jurisdiction of the New 
Zealand Courts.  

Contact Details 

 

New Zealand:  

 

 

 

Rest of World:  

Hansa Products Limited    

 

Please refer to 

www.hansaproducts.com

  

PO Box 10323, Te Rapa 

 

 

for a current list of our authorised dealers  

Hamilton 

 

 

 

and contact details relevant to your territory. 

Summary of Contents for C27





























Reviews: