background image

 

 

19 

MAINTENANCE 

1.

  The  appliance  should  be  inspected  before  initial  use  and  inspected  and  cleaned  at  least 

annually by a qualified service person. 

2.

  Tampering  is  DANGEROUS  and  voids  all  warranties.  Any  component  that  is  found  to  be 

faulty, must be replaced with an approved component. 

3.

  To obtain proper operation, it is imperative that the burner flame characteristics are constant, 

not lifting or floating. For a clean burn the unit is designed to run at full flow. If not operating 
at full fuel flow black smoke may start to occur. Always operate at full fuel flow to burn clean 
and prevent smoke. Dirty logs can be easily cleaned off with water and light soap. 

4.

  Periodically remove the logs and examine the burner and its components. If dirty, clean with 

a soft brush and soapy water solution. Also examine the area around the burner. Any dirt or 
foreign  material,  such  as  spider  webs  or  nests  in  this  area  should  be  removed.  This  will 
ensure long life, safe and trouble free operation. 

5.

  Periodically check the hose connecting the LP gas cylinder or city network gas to ensure it is 

not cracked or damaged in any way. 

 

INSPECTION AFTER REPAIR

  

Any repairs must be performed by a qualified installer, service agency or your gas provider. 
 
1.  Check all the joints. 
2.  Smell all around the appliance area for gas odors and test for gas leaks according to 

Testing 

for Leaks

 on page 13. 

3.  Light the appliance according to the 

LIGHTING INSTRUCTIONS

 on page 15. 

 

NOTE: 

Carbon  (soot)  may  built  up  on  the  surface  of  the  logs  over  time  or  with  extended  use. 

This is more likely to occur when using LP gas. The soot should be cleaned off the surfaces of 
the imitation logs periodically to prevent excessive build up. To clean the logs, be sure the fire is 
out,  the  gas  supply  is  turned  off  and  the  logs  are  cool  to  the  touch.  The  soot  can  then  be 
brushed  of  with  a  dry  bristle  brush  or  cloth.  Take  care  while  cleaning  the  logs  as  they  can 
become damaged if mishandled. Care should be taken to dispose of the soot and the cleaning 
materials properly. Keep away from clothing and outdoor furniture. 
During the cold winter months or in colder climates, it is recommended to disconnect the built-in 
gas fire burner kit and cover the lid.  

 

Distributor: 
 
 
 
 

 

 
HAPPY COCOONING B.V. 
Provinciënbaan 1 
5121 DK Rijen 
The Netherlands 
Tel: +31 (0) 161 750270 
Fax: +31 (0) 161 750375

 

Summary of Contents for 4001BIS/I2 Plus





















Reviews: