172
11-2-7 shooting (Malfunction of thread break detection)
Trouble Factor Cause of trouble and measure
Page
Malfunction
of
Mechanical
1. Trouble in turning detection roller.
thread break
1-1 Clean roller shaft holder.
detection
1-2 Check if slit disc doesn't contacts sensor.
(empty
1-3 Clean sensor if dust gets stuck.
detection)
1-4 Check if cord doesn't contacts slit disc.
1-5 Check Disconnection of cable.
1-6 Check clog of thread detection roller. Roller shaft should haveclearance.
2. Check circuit board.
2-1 Replace of LCD-CE board.
2-2 Replace of TC 12 board.
2-3 Replace of CONT-D2 board. 4-2
3. Sometimes needle bar doesn’t work when start sewing.
3-1 Replace of needle bar driver. 3-2-6
3-2 Adjust of jump device position. 3-2-7
3-3 Clean and overhaul of Jump device. 3-2-14
3-4 Replace of Jump device.
Operator 1. No thread is passed through detecting roller.
1-1 Pass thread properly.
(4-7)
2. Is thread tension proper?
2-1 Observing sewing rhythm, adjust thread tension properly.
(4-5) (8-1)
3. Is proper detection sensitivity of thread cut selected?
3-1
Select detection sensitivity according to sewing condition of thread and cloth etc.
(5-1)
Environment
1. Is there any device to yield lints etc. around the embroidery.
1-1 Keep it off the embroidery machine.
1-2 Move the embroidery machine to other place.
2.
Doesn't thread go beyond control by wind? (thread comes off from needle hole by loosing)
2-1 Keep thread off wind.
2-2 Move the embroidery machine to other place.
Thread & 1. Isn't silicone agent used on thread?
Cloth (Thread slips at detecting roller part due to adhere of silicone.)
1-1 Clean silicone agent attached to detecting roller groove.
( ) ----- Reference instruction book
Summary of Contents for HCD2-1501-40
