18
2
No. message Error measure page
120 Memory error It became impossible to retain contents (1) Turn power off once and turn on again.
of memory. (2) If problem recurs frequently, replace
LCD-CE board. 5-2
130 Disk error Unable to communicate continuously (1)Turn off power source once and turn it on
with memory media. again.
(2)Memory media reading processor may
defective. Replace the LCD-CE board. 5-2
131 Device no ready Memory media is not set. Check if memory media is properly set. ( 5-5 )
133 Bad disk Improper or faulty memory media. (1)Memory media might be not eadable with ( 5-5)
the machine. Prepare readable memory
media for the machine.
(2)Memory media might be defective.
Prepare another memory card or data
disk which is not defective.
(3)Initialize the memory media
if it is not initialized.
141 Not found name Designated pattern is not found. Memory media might be not readable with ( 5-5 )
the machine.
Prepare readable memory media for the
machine.
142 Disk full Memory media is full to capacity. Clear unnecessary patterns or use a different
memory media.
143 Multi name Another pattern with same name has Change name, use a different memory media,
been detected while attempting to or overwrite existing pattern.
write to memory media.
190 Cut blade Thread cut knife is not at stop position. (1)Restore the moving knife to stop position. ( 24-6 )
(2) Check dirt of trim sensor or position of slit.
(3)Modify the adjustment if the problem repeats.
(4) Adjust sensor position.
191 Cut Sensor Thread cutting device did not (1) Press the [CUT] button 2~3 times.
move correctly. (2) Check if thread is twined around the moving
knife.
(3) If photo sensor is stained, clean.
(4) Replace the photo sensor board.
193 Catcher Thread catch hook is not in its (1)Check if mistake is found in thread cut. ( 24-8 )
stop position. If found, cut thread and move thread catch
hook to proper position.
(2)Adjust and correct trouble that hinders
motion of thread catch hook.
( ) ----- Reference instruction book
Summary of Contents for HCD2-1501-40
