HAPRO Luxura V10 Owner'S Manual Download

Page: 5 / 150

Congratulations on the purchase of your Hapro sunbed. Your new sunbed has been

manufactured with the utmost care and attention and consists of high-quality parts.

All Hapro sunbeds have been developed to give you the best possible tan, whilst

complying with the strictest applicable European standards.

1 Contact your authorised Hapro dealer

immediately if this unit does not function as
outlined in this manual.

2 Do not operate this unit in humid spaces.

3 Always make sure the fuses can carry the load.

This unit has to be protected by ground fault
circuit interrupter (GFCI) of 0.03A.

4 Always disconnect the power to the unit at

the wall breaker (isolator) when servicing or
cleaning the in-side construction of the
cabine. Maintenance for which the procedure
is not described in this manual should only be
carried out by a qualifi ed electrician. Never
clean the electrical components with fl uids.

5 Ensure that the canopy does not touch the

wall when opened.

6 Prevent the acrylic sheets from coming into

contact with sharp objects.

7 This unit may not be operated if:

•

the user is not wearing protective uv-

goggles

•

the blue or white facial glass is cracked or

broken

•

the acrylic panel in the canopy and/or bench

is missing

•

one or more of the fans in the unit are not

functioning properly

•

the timing mechanism is not functioning

properly

•

the temperature inside the cabin is 30°C or

higher

8 To ensure maximum tanning eff ectiveness,

change the acrylic sheet after every 1200
hours of operation.

9 To ensure maximum tanning eff ectiveness,

replace the lamps and the facial tanning
lamps according to manufacturer´s
instructions.

10 Check local regulations to fi nd out the proper

procedure for lamp disposal.

11 Note: only a special acrylic cleaner may be

used to clean the acrylic sheet. Never use
cleaners that contain alcohol, as these can
damage the acrylic sheet.

12 The UV-type of the tanning unit is indicated

on the specifi cation sticker.

13 Ultraviolet radiation from the sun or UV

appliances can cause skin or eye damage.
These biological eff ects depend upon the
quality and quantity of the radiation as well as
the skin and eye sensitivity of the individual.

14 Excessive exposure may cause skin to burn.

Excessive repeated exposure to ultraviolet
radiation from the sun or UV appliances may
lead to premature ageing of the skin as well
as increase risk of skin tumours. These risks
increase with increasing cumulative UV
exposure. Exposure at an early age increases
the risk of skin damage later in life.

15 The unprotected eye may develop surface

inflammation and in some cases, after a

cataract operation for example, damage may
accur to the retina after eccessive exposure.
Cataracts may develop after prolonged
exposures.

16 If the supply cord is damaged, it must be

replaced by the manufacturer or service
agent or a similarly qualifi ed person in order
to avoid a hazard.

17 To replace lamps and starters, remove by

turning a quarter turn to the left. Placement
of new lamps and starters is done in the
reverse to the above mentioned procedure.

18 When installing the equipment, follow the

recommended minimum distances listed in
the “Dimensions / Placement” chapter.

19 Where applicable, clean the dust fi lters after

every 50 hours of use. Regularly check the
dust fi lters.

20 Children should be supervised to ensure that

they do not play with the tanning unit.

21 Non-users, especially children, must not be

present when the appliance is being
operated.

Read this first

The information contained in this manual regarding assembly and operation should be followed in full. Failure to do so may render the product
warranty or liability on behalf of the supplier null and void. If there is any uncertainty as to whether the instructions contained in this manual
have been followed properly and entirely, you should contact the supplier of the sunbeds.

Note

Please consult enclosed tanning schedule for advised tanning times.
Repairs may only be carried out by qualifi ed personnel.
Always disconnect the main power at the circuit breaker before servicing or repairing the unit.

1: ENG