background image

11

WIRING

      

WARNING:

 To reduce the risk of fire, electrical shock or personal injury, wire connectors provided 

with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If 
your house wire is larger than 12-gauge or there is more than one house wire to connect to the 
corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.

      

CAUTION:

 Be sure outlet box is properly grounded and that a ground (green or bare) wire is 

present.

      

WARNING:

 If house wires are different colors than referred to in the following steps, stop 

immediately. A professional electrician is recommended to determine wiring.

      

WARNING:

 Using a full range dimmer switch (not included) to control fan speed will cause a loud 

humming noise from fan. To reduce the risk of fire or electrical shock, do NOT use a full range dimmer 
switch to control fan speed.

CLOSEMOUNT-STYLE FAN MOUNTING

3. Pull wires up through hole in the middle of the 

canopy (B) and attach canopy (B) to motor 
housing (D) using the three previously removed 
screws/lock washers.

3

B

D

Screw/Lock Washer

Temporarily hang fan on the tab on the mounting 
bracket (C) using one of the 

non-slotted

 holes in 

the canopy (B).

4.

Tab

C

4

B

Summary of Contents for 2599780






















Reviews: