background image

9

WIRING

 

WARNING:

 To reduce the risk of fire, electrical shock or personal injury, wire connectors 

provided with this fan are designed to accept only one 12-gauge house wire and two lead wires 

from the fan. If your house wire is larger than 12-gauge and/or there is more than one house wire to 

connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.

CAUTION:

 Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present.

1.  Connect supply and fan wires according to the 

diagram and these steps:
• Connect the Green wire from the mounting bracket 

(A) to the Bare/Green (ground) supply wire.  

• Push the White (neutral) supply wire into the 

empty wire hole of the push-in wire connector 

preassembled to the White wire from the receiver of 

remote pack (L). 

• Push the Black (hot) supply wire into the empty wire 

hole in push-in wire connector preassembled to the 

Black wire from the receiver of remote pack (L).

   

Note:

 The Black wire is hot power for the fan. The 

White wire is neutral for the fan and light kit. The 

Green wire is the ground wire. If supply wires are 

different colors than referred to above, a professional 

electrician should determine the proper wiring. 

 

Hardware Used

AA

Wire Connector

x 1

2. 

Raise the fan and place the canopy (B) on the hook 

on the mounting bracket (A). Connect the 3-pin 

connector from the fan to the 3-pin connector from 

the receiver. 

Important:

 Receiver should not come in 

contact with hook on mounting bracket.

3.  

Wrap electrical tape (not included) around the wire 

connector (AA) down to the wire.

     Turn the spliced/taped wires upward and gently push 

the wires and wire connector (AA) into the outlet box.

 

WARNING:

 Ensure no wire strands are visible 

after making connections. Place the Green and White 

wire connections on the opposite side of the outlet 

box from the Black. 

1

3

AA

A

A

2

AA

3-Pin 

Connector

Receiver

Receiver

White (neutral)

Bare/Green (ground)

Push-in

Connector

Blac

k

Black (hot)

Whit

e

WARNING:

 Do NOT wire 

the fan to a wall control.

Summary of Contents for 3025022


















Reviews: