background image

6

3.   

WARNING

7RUHGXFHWKHULVNRI¿UHRUHOHFWULFVKRFNGRQRWXVHWKHIDQZLWKDQ\VROLGVWDWH

speed control device or control fan speed with a full range dimmer switch.

4.   

WARNING

7RUHGXFHWKHULVNRI¿UHHOHFWULFVKRFNRUSHUVRQDOLQMXU\GRQRWEHQGWKH

blade arms when installing them, balancing the blades, or cleaning the fan.  Do not insert 
objects between the rotating fan blades.

5.   

WARNING

: To reduce the risk of personal injury, use only parts provided with this fan.  The 

use of parts OTHER than those provided with this fan will void the warranty.

1.   

CAUTION

: Be sure outlet box is properly grounded or that a ground (green or bare) wire is 

present.
After opening top of carton, remove mounting hardware package from foam inserts.  Remove 

PRWRUIURPSDFNLQJDQGSODFHRQFDUSHWRURQIRDPWRDYRLGGDPDJHWR¿QLVK

2.   

CAUTION

: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that 

they are secured.

WARNING

CAUTION

PREPARATION

Before beginning assembly of product, make sure  all parts are present.  Compare parts with package 
contents list and hardware contents above.  If any part is missing or damaged, do not attempt to 
assembly the product.  Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety 
Glasses, Step Ladder and Wire Strippers

Helpful tools (not included): AC Tester Light, Tape Measure, Wiring Handbook, and Wire Cutters

Summary of Contents for Casual-3-2011



















Reviews: