background image

 

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the 
product. 

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for 
repairs, it must be shipped in its original packaging to ensure proper protection against damage that 
might exceed the initial cause for return.
• 

Make sure that all electrical connections comply with local codes, ordinances, the National Electrical 

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook 
(available at Lowe's) if you are unfamiliar with installing electrical wiring.

 

• 

Make sure the installation site you choose allows a minimum clearance

 of 

7 feet from the blades to 

the floor and at least 30 in. from the end of the blades to any obstruction.

 

• 

 After you install the fan, make sure that all connections are secure to prevent the fan from falling.

•  The net weight of this fan including the light kit is: 15.87 lbs. (7.2 kg).

Safety Information ..........................................................................................................2 - 3

Package Contents ...............................................................................................................4              

Hardware Contents ..........................................................................................................................5

Preparation ..........................................................................................................................5

Initial Installation .............................................................................................................6 - 7

Downrod Style Fan Mounting .........................................................................................7 - 9

Closemount Style Fan Mounting ..................................................................................9 - 10

Wiring .........................................................................................................................11 - 12

Final Installation ..........................................................................................................12 - 14

Operation Instructions ................................................................................................14 - 15

Care and Maintenance ......................................................................................................15

Troubleshooting..................................................................................................................16

Warranty ............................................................................................................................17

Replacement Parts List .....................................................................................................18
 

TABLE OF CONTENTS

2

Lowes.com/harborbreeze

SAFETY INFORMATION

Summary of Contents for CLASSIC STYLE BDB52LW5N



















Reviews: