background image

16

FCC WARNING

This device (including remote control and LED module) complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. Please note that changes or

modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

Note: Both the remote control and LED module have been tested and found to comply with the limits

for Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protectionagainst harmful interference in a residential installation.

The remote control generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

L G Sourcing, Inc.

1000 Lowe’s Blvd.

Mooresville, NC 28117

1-800-643-0067

Summary of Contents for HTD20005



















Reviews: