background image

WIRING

12

       

WARNING:

 To reduce the risk of fire, electrical shock or personal injury, wire connectors 

provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from 
the fan. If your house wire is larger than 12-gauge or there is more than one house wire to connect to 
the corresponding fan lead wires, consult an electrician for the proper size wire connectors to use.

       

CAUTION:

 Be sure outlet box is properly grounded and that a ground (green or bare) wire is 

present.

       

WARNING:

 If house wires are different colors than referred to in the following steps, stop 

immediately. A professional electrician is recommended to determine wiring.

       

WARNING:

 Using a full range dimmer switch (not included) to control fan speed will cause a loud 

humming noise from fan. To reduce the risk of fire or electrical shock, do NOT use a full range 
dimmer switch to control fan speed.

 1.  Make the necessary wiring connections for 

remote control operation as detailed below and 
in the figure. For each wire connection, use one 
of the wire connectors (CC), making sure to 
screw wire connector (CC) on in a clockwise 
direction.

CAUTION:

 Assistance from another person is 

recommended for this step.

Connect all GROUND (GREEN) wires from fan 
(on downrod (A), if applicable, and mounting 
bracket (C)) to BARE/GREEN supply wire from 
ceiling.

Connect BLACK wire (labeled AC IN L) from 
remote control receiver (O) to BLACK supply 
wire from ceiling.

Connect WHITE wire (labeled AC IN N) from 
remote control receiver (O) to WHITE supply 
wire from ceiling.

Connect WHITE wire (labeled TO MOTOR N) 
from remote control receiver (O) to WHITE wire 
from motor housing (D).

Connect BLACK wire (labeled TO MOTOR L) 
from remote control receiver (O) to BLACK wire 
from motor housing (D).

Connect BLUE wire (labeled FOR LIGHT) from 
remote control receiver (O) to BLUE wire from 
motor housing (D).

O

1

WHITE SUPPLY WIRE

BLACK SUPPLY WIRE

BLACK

BLACK

WHITE

BLUE

BLUE

WHITE

BLACK

AC IN L

WHITE

AC IN N

WHITE

GROUND (GREEN OR BARE)

GROUND 

(GREEN OR BARE)

BLACK

FROM
RECEIVER

FROM 
FAN

FROM
RECEIVER

FROM
CEILING

Summary of Contents for TG44BNK3D1RC




















Reviews: