background image

SKU  43476                                          PAGE 2

 REV. 10/03

SPECIFICATIONS

SAVE THIS MANUAL

You will need the manual for the safety warnings and precautions, assembly,
operating and maintenance procedures, Parts List and Diagram.  Keep your
invoice with this manual.  Write the invoice number on the inside of the front cover.
Keep the manual and invoice in a safe and dry place for future reference.

                       ITEM                                                       DESCRIPTION

Cast Aluminum

Cream White Enamel

14.50 Lbs.

10-1/4” H x 3-1/4” W x 17-1/2” L

Up To 12” Wide

Polyethylene / Polypropylene Bags

Spring Loaded

UL Approved

63”

110-VOLT AC /  50-60 HZ / 300 WATTS

Adjustable

Heat Element (Qty: 2)
Teflon Cloth (Qty: 2)

Construction

Finish

Net Weight

Overall Dimensions

Sealing Capacity

Sealing Materials

Sealing Arm

Cord/Plug/Switch Rating

Cord Length

Electrical Requirements

Timer

Accessories

       SAFETY WARNINGS AND PRECAUTIONS

1.

KEEP WORK AREA CLEAN AND DRY.  

Cluttered, damp or wet work areas invite

injuries.

2.

KEEP CHILDREN AWAY FROM WORK AREA.  

Do not allow children to handle

this product.

3.

STORE IDLE EQUIPMENT.  

When not in use, tools must be stored in a dry loca-

tion to inhibit rust.  Always lock up tools and keep out of reach of children.

4.

DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR
DRUGS.  

Read warning labels on prescriptions to determine if your judgment or

reflexes are impaired while taking drugs.  If there is any doubt, do not attempt to
use this product.

43476 manual.p65

10/15/03, 3:16 PM

2

Brought to You by Augusta Flint

Summary of Contents for 43476









Reviews: