background image

SKU  43476                                            PAGE 3

5.

USE EYE PROTECTION.  

Always wear ANSI approved impact safety glasses.

The impact safety glasses are available from Harbor Freight Tools.

6.

DRESS SAFELY.  

Do not wear loose clothing or jewelry as they can become

caught in moving parts.  Wear a protective hair covering to prevent long hair from
becoming caught in the moving parts.

7.

DO NOT OVERREACH.  

Keep proper footing and balance at all times.

8.

STAY ALERT.  

Watch what you are doing at all times.  Use common sense.

Do not operate this product when you are tired or distracted from the job at hand.
The warnings, cautions, and instructions discussed in this manual cannot cover all
possible conditions and situations that may occur.  It must be understood by the
operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.

9.

OBSERVE WORK AREA CONDITIONS.  

Do not use machines or power tools

in damp or wet locations.  Do not expose to rain.  Keep work area well lighted.
Do not use electrically powered tools in the presence of flammable gases or
liquids.  Do not submerge this product in any liquid.

10.

  CHECK FOR DAMAGED PARTS.  

Before using this product, carefully check that

  it will operate properly and perform its intended function.  Check for damaged
  parts and any other conditions that may affect its operation.  Replace or repair
  damaged or worn parts immediately.

11.

  REPLACEMENT PARTS AND ACCESSORIES.  

When servicing, use only identi-

  cal replacement parts.  Only use accessories intended for use with this product.
  Approved accessories are available from Harbor Freight Tools.

12.

  MAINTAIN THIS PRODUCT WITH CARE.  

Keep this product clean and dry, and

  moving parts lightly lubricated for better and safer performance.  Inspect electrical
  cord periodically and, if damaged, have it repaired or replaced by an authorized
  technician.  Keep handle dry, clean and free from oil, grease, and solvents.

13.

  MAINTENANCE:  

For your safety, service and maintenance should be performed

  regularly by a qualified technician

14.

  USE THE RIGHT PRODUCT FOR THE RIGHT JOB

.  There are certain applica-

  tions for which this product was designed.  Do not use this product for a purpose
  for which it was not intended

43476 manual.p65

10/15/03, 3:16 PM

3

Brought to You by Augusta Flint

Summary of Contents for 43476









Reviews: