background image

Page 3

For technical questions, please call 1-800-444-3353.

Item 65040 

        

use

1. 

use only for water or water-based fertilizers, 

herbicides, pesticides and sealers.  Do not use 

to spray combustible or corrosive chemicals. 

2.  Do not point the Sprayer at yourself, 

other people or animals.

3.  Industrial applications must follow 

OSHA requirements.

4.  Make sure the liquid used in the 

Sprayer is not dirty or sandy.

5.  This product is not a toy.  Do not allow 

children to play with or near this item.

6.  Use as intended only.

7.  Inspect before every use; do not use 

if parts are loose or damaged.

8.  Maintain product labels and nameplates.  

These carry important safety information.  

If unreadable or missing, contact 

Harbor Freight Tools for a replacement.

9.  The warnings and cautions discussed in this 

manual cannot cover all possible conditions 

and situations that may occur.  The operator 

must understand that common sense and 

caution are factors that cannot be built into this 

product, but must be supplied by the operator.

Service

1. 

have your Sprayer serviced by a qualified repair 

person using only identical replacement parts.

   

This will ensure that the safety of 

the tool is maintained.

2.  Store idle tools and equipment out of 

reach of children and other untrained 

people.  Tools and equipment are dangerous 

in the hands of untrained users.

3.  Maintain the Sprayer with care.  Keep 

this product clean.  A properly maintained 

Sprayer is easier to control.

 SaVE thESE inStRuctiOnS.

Summary of Contents for 65040













Reviews: