Harbor Freight Tools 65785, Instructions And Precautions

SKU 65785 

For technical questions, please call 1-800-444-3353. 

Page 4

.

Manually turn on the unit to be controlled.

7. 

Press and hold the Code Search Button until 

8. 

the LED stays on.  Release the Code Search 

Button.
Point the Remote at the unit and press the 

9. 

Power Button until the unit turns off.
If the unit does not turn off, press the Chan-

10. 

nel Up Button repeatedly until the unit 

changes the channel.
Once the unit is fully functional, press and 

11. 

release the Mute Button (4) to save and pro-

gram the code.
Test all other buttons on the Remote to verify 

12. 

they work properly.

please note: 

13. 

When the Remote is set and 

no keys have been pressed for fifteen sec

-

onds, the Code Search feature will automati-

cally turn off. 

IdentIFYIng code

To program the code into the Remote, first 

1. 

press Code Search Button until the LED Indi-

cator turns on.  Then release the button.
Press and quickly release the correct product 

2. 

key (TV, VCR, etc.) from the row of Devise 

Select Controls (9).  The LED Indicator will 

blink and remain on.
Press the Code Search Button again.  Con-

3. 

tinue to do so until the LED Indicator stays 

on. 

To find the first code, enter the numbers (0-9) 

4. 

consecutively.  When the LED light flashes, 

this will set the first code. Repeat until you 

find the second code and then the third code.  

You will find each code manually by pressing 

all ten keys to see which one responds.
Please note: When the control is set and no 

5. 

keys have been pressed for fifteen seconds, 

the Code Search feature will automatically 

turn off. 

dIrect code entrY

Press and hold the Code Search Button until 

1. 

the LED stays on.  Release the Code Search 

Button.

Press and quickly release the correct product 

2. 

key (TV, VCR, etc.) from the row of Devise 

Select Controls (9). The LED Indicator will 

blink and remain on.
Enter the corresponding 3-digit code.  After a 

3. 

valid code entry the LED Indicator turns off.  

In case of an invalid code entry, the LED will 

flash.

With the unit (TV, DVD) on, press the Chan-

4. 

nel Up Button (5).  If the TV responds, no 

further programming is needed.  If it does 

not, try another code listed from your brand.
Please Note: Some codes do not offer the 

5. 

Remote full access so you may difficulties 

with one code. Try another until one works 

properly.
If the unit does not respond after trying all the 

6. 

codes listed for your brand or if your brand is 

not listed, do a manual code search by doing 

the following steps.
Manually turn on the unit to be controlled.

7. 

Press and hold the Code Search Button until 

8. 

the LED stays on.  Release the Code Search 

Button.
Press and quickly release the correct product 

9. 

key (TV, VCR, etc.) from the row of Devise 

Select Controls. The LED will blink off once. 
Point Remote at unit you wish to control.

10. 

Press the Power Button (3) repeatedly (it 

11. 

may take up to 300 times) until the device to 

be controlled changes channel. The LED will 

blink off with each press of the button.
Press and release the Enter Button to install 

12. 

the code.

please note:

13. 

 Most users store their unit 

codes depending on the device, such as 

storing TV codes for TV. But you can store 

codes for other devices.  For instance, you 

may store a DVD code under a cable and 

store something else under DVD.  In order to 

do this, you must program that device code 

by direct code entry or search.  

please note: 

If the device do not have a 

Channel Up Button and uses Play (VCR 

only) or Power instead, the code search 

starts from the currently stored three digits 

number under that mode.

For tV only (direct entry) continued

REV 09l