background image

Page 3

SKU 94515

for technical questions, please call 1-800-444-3353.

SpEcificAtiONS

Overall Dimensions

51

1

/

2

” L x 74

1

/

2

” W x 81” H

Window Dimensions

22

3

/

4

” L x 20” W

Door Dimensions

62

3

/

4

” H x 22

3

/

4

” W

Materials

Aluminum Frame

Transparent Polycarbonate Sheets

Note:  Diagrams  within  this  manual  are  for  reference  only  and  are  not  necessarily  to 

scale.

Save this Manual

You will need this manual for the safety warnings and precautions, assembly, inspec-

tion, maintenance and cleaning procedures, parts list and assembly diagram.  Keep your 
invoice with this manual.  Write the invoice number on the inside of the front cover.  Keep 
this manual and invoice in a safe and dry place for future reference.

GENERAl SAfEty WARNiNGS ANd pREcAUtiONS

KEEp WORK AREA clEAN ANd dRy.  

1. 

Cluttered, damp, or wet work areas invite 

injuries.

KEEp cHildREN AWAy fROM GREENHOUSE.  

2. 

Do not allow children to play in 

or climb on this product.  Although this greenhouse does include some protective 
covers, there are still some exposed sharp edges.  In addition, protective covers 
may fall off in time.  Children must be supervised if allowed near the greenhouse.

dO NOt ASSEMblE tHiS pROdUct if UNdER tHE iNflUENcE Of AlcOHOl 

3. 

OR dRUGS.  Read warning labels on prescriptions to determine if your judgement 
or reflexes are impaired while taking drugs.  If there is any doubt, do not attempt to 
assemble this product.

USE EyE pROtEctiON.  

4. 

Wear ANSI-approved safety impact eye goggles when 

assembling this product.  ANSI-approved safety impact eye goggles are available 
from Harbor Freight Tools.

dO NOt OVERREAcH.

5. 

  Keep proper footing and balance at all times to prevent 

tripping, falling, back injury, etcetera.

StAy AlERt.

6. 

  Watch what you are doing at all times.  Use common sense.  Do 

not attempt to assemble this product when you are tired or distracted from the job 
at hand.

cHEcK fOR dAMAGEd pARtS.

7. 

  Before using this product, carefully check that 

it will operate properly and perform its intended function.  Check for damaged parts 

REV 10h

Summary of Contents for 94515



















Reviews: