background image

Page 4

SKU 94515

for technical questions, please call 1-800-444-3353.

and any other conditions that may affect the operation of this product.  Replace or 
repair damaged or worn parts immediately.

REplAcEMENt pARtS ANd AccESSORiES:

8. 

 When servicing, use only identical 

replacement parts.  Only use accessories intended for use with this product.  Ap-
proved accessories are available from Harbor Freight Tools.

MAiNtAiN tHiS pROdUct WitH cARE.

9. 

  Keep this product clean and dry for 

better performance.

MAiNtENANcE:

10. 

  For your safety, service and maintenance should be performed 

regularly by a qualified technician.

USE tHE  RiGHt  pROdUct  fOR tHE  jOb.

11. 

    Do  not  attempt  to  force  a  small 

product to do the work of a larger industrial product.  There are certain applications 
for which this product was designed.  It will do the job better and more safely in the 
manner for which it was intended.  Do not modify this product, and do not use this 
product for a purpose for which it was not intended.

MAiNtAiN A SAfE WORKiNG ENViRONMENt.  

12. 

Keep the work area well lit.  Make 

sure there is adequate surrounding workspace.  Avoid high traffic areas.  Always 
keep the work area free of obstructions, grease, oil, trash, and other debris.

pROpER GREENHOUSE lOcAtiON:

13. 

 Make sure the Greenhouse is located on 

a flat, level, surface.

WARNiNG: 

14. 

The brass bushings in the door rollers of this product contain lead, a 

chemical known to the State of California to cause birth defects (or other reproduc-
tive harm). (California Health & Safety code § 25249.5, et seq.)

tHiS UNit cONtAiNS piEcES WitH SHARp EdGES.

15. 

  The machined edges of 

the aluminum parts and the ends of the panel clips may be sharp.  Handle all parts 
carefully.

SNOW/dEbRiS AccUMUlAtiON HAZARd.

16. 

  The heavy weight of accumulated 

snow or other debris can cause parts of this greenhouse to buckle suddenly.  Do 
not allow debris to accumulate on top of the greenhouse.  If snowfall is expected, 
place additional supports (not provided) underneath the Crown.  

NEVER enter a 

greenhouse with accumulated debris on top.

WARNiNG:

17. 

 The warnings, precautions, and instructions discussed in this manual 

cannot cover all possible conditions and situations that may occur.  The operator 
must understand that common sense and caution are factors, which cannot be built 
into this product, but must be supplied by the operator.

Summary of Contents for 94515



















Reviews: