background image

47

ALPHA

Fault

Probable cause

Control / remedy

EC Operating unit

Operating unit not

Blown fuse(s).

Check mechanical function of microswitches.

functioning

Use cleaning/lubricating agent if the switch
does not operate freely.

Check motor. 450-500 milli-Amperes max.
Change motor, if over.

Wrong polarity.

Brown - pos. (+).  Blue  - neg. (-).

Valves not closing properly.

Check valve seals for obstructions.

Check microswitch plate position. Loosen
screws holding plate a 

1

/

2

 turn.

No power.

Wrong polarity. Check that brown is pos. (+),
Blue is neg. (-).

Check print plate for dry solders or loose
connections.

D.A.H. Hydraulic system

No boom movements

Insufficient oil pressure

Check oil pressure - min. 130 bar, max. 150 bar.

when activated

Check hydraulic oil level

Insufficient oil supply.

Check hydraulic oil level.

Blown fuse.

Check / replace fuse in junction box.

Bad / corroded electrical connections

Check / clean connections, etc.

Insufficient power supply.

Voltage on activated solenoid valve must be
more than 8 Volts. Use wires of at least 4 mm

2

for power supply.

Defect relay / diodes in junction box.

Check relays, diodes and soldering at PCB in
junction box

Wrong polarity.

Check polarity. White pos. (

+

) Blue neg. (

-

).

Individual ram

Clogged restrictor

Dismantle and clean restrictor

does not move

Summary of Contents for ALPHA 2000





















































Reviews: