background image

8

ALPHA

• The position lamps’ and head lamps’ dipped beam

are switched on by turning the multi-functional lever
and is indicated by the pilot lamp

• The main beam is activated by pressing the lever

downwards and is indicated by the pilot lamp.

• To flash the main beam pull the lever upwards.
• The directional indicators are operated by pushing

the lever forward (right) or backward (left) and indi-
cated by the pilot lamp.

• The horn is activated by depressing the stalk end.

Rotating amber warning beacon switch

Is recommended to be used when driving on public
roads. Note local regulations regarding use of rotating
warning beacon.

Controls and switches, dash board

1. Adjustable air flow louvres
2. Console for HARDI PILOT
3. Boom outer section folding, left
4. Boom inner sections folding
5. Boom outer section folding, right
6. Boom pendulum locking device
7. 4-wheel steering switch
8. Engine throttle lever
9. Not used

10. Not used
11.  Engine STOP warning lamp
12.  Spraying pump control lamp
13.  Engine pre-heating control lamp
14.  Battery isolator switch control lamp
15.  Windscreen wiper switch
16.  Working lamps switch
17.  Wind screen washer switch
18.  Auxiliary lights switch
19.  Not used

20.  Screen wash reservoir
21.  On/off switch for HARDI PILOT
22.  Fuse box
23.  Cab interior lamp
24.  Fan control 3-speed switch
25.  Fuse box
26.  Air conditioning warning buzzer
27.  Air conditioning “over pressure” control lamp
28.  Air conditioning “low pressure” control lamp
29.  Parking brake lever
30.  Air conditioning temperature control
31.  Cab heater / defroster
32.  Cab air flow louvres
33.  Spraying pump switch
34.  Hydrostatic transmission control lever
35.  Hydrostatic front wheel motors Fast / Slow switch
36.  Do. Rear
37.  Control lamp, realignment of front wheels

(4-wheel steering)

38.  Control lamp, realignment of rear wheels

(4-wheel steering)

39. Control lamp, 4-wheel steering.
40. 4-Wheel steering AUTO/MANUAL switch
41. Pedal, 4-wheel steering
42. Switch for Electronic Anti-Spin System, SAPE

• Overload of engine - reduce driving speed
• Clogged cooler radiator fins - clean the radiator
• Coolant level low - refill with hot coolant to correct

level

• Engine oil level low - refill to correct level.

If none of the above is solving the problem, call the en-
gine service agent.

Fuse box

Regarding fuse diagram - see “Electrical system mainte-
nance”

Multi functional control stalk

1

1

41

2

T060-0004

T064-0007

T060-0021

Summary of Contents for ALPHA 2000





















































Reviews: