Hardi Navigator 550M Centrifugal Supplement To Operating Instructions Download

Page: 8 / 16

SUPPLEMENT TO NAV. 550M, 800M, 1000M CENTRIFUGAL OPERATOR'S MANUAL

Control boxes

The Spraybox and controller (optional) are ﬁ tted in the tractor cabin at
a convenient place. HARDI

rec om mends using an electric distribution

box (ref. no. 817925) to ensure a good power supply to various 12V
attachments.

Installation of control unit brackets

The supplied tractor pillar bracket

(A)

has a hole spacing of 3.9 in.

(100mm) and 4.7 in. (120mm). Check tractor instructions manual for
information regarding attachment points.

Three tubes

(B)

are supplied. One, two or all three may be used. They

can be bent and shortened. A spacer

(C)

is also supplied to allow

further attachment possibilities. Find the best solution for your tractor or
vehicle.

Tube

(B)

plate is staggered, so if correctly orientated, all boxes will line

up.

Summary of Contents for Navigator 550M Centrifugal

















Search results

Summary of Contents for Navigator 550M Centrifugal

Reviews:

Related manuals for Navigator 550M Centrifugal

Brands by name

Popular brands

Hardi Navigator 550M Centrifugal, Supplement To Operating Instructions

Search results

Summary of Contents for Navigator 550M Centrifugal

Reviews:

Related manuals for Navigator 550M Centrifugal

Brands by name

Popular brands