HARDKERNEL ODROID-UPS3 Manual Download | Manualshive

Page: 4 / 10

background image

Last update: 2020/10/21
07:03

accessory:power_supply_battery:odroid-ups3 http://wiki.odroid.com/accessory/power_supply_battery/odroid-ups3

http://wiki.odroid.com/

Printed on 2020/11/09 14:28

Ensure that slide switch SW1 is to the left to enable power output.
Even when SW1 is oﬀ, the charging function keeps working.

Assemble guide

Assemble as the UPS3 as shown in Figure.

Pin assignment to conﬁgure SW

There are three signals to control auto shutdown and wake-up based on battery status.

«
...
2
3
4
5
6
...
»

Summary of Contents for ODROID-UPS3











Reviews:

No comments

Related manuals for ODROID-UPS3

Brand: R&D Pages: 55

Power Protection Active 1000

Brand: Chloride Pages: 45

Brand: Eaton Pages: 143

Brand: Eaton Pages: 10

Brand: Eaton Pages: 20

Brand: Koblenz Pages: 4

Brand: LEGRAND Pages: 111

DAKER DK Plus 3 106 60

Brand: LEGRAND Pages: 124

Brand: Kebo Pages: 4

Brand: Digitus Pages: 9

Brand: GE Pages: 10

Brand: GE Pages: 66

PEGASUS II 10 KVA

Brand: Effekta Pages: 128

DreamBook Solar UPS Battery Bag

Brand: Pioneer Pages: 23

UPS System AVRX550U

Brand: Tripp Lite Pages: 18

Brand: Tripp Lite Pages: 12

UPS5000-A-800 Series

Brand: Huawei Pages: 13

Brand: Avaya Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands