background image

3

112787

During Operation of Tool
1. Keep all parts of body away from staple exit on tool.
2. Never point tool at anyone.
3. Keep children, animals, and bystanders away from tool and extension cord

at all times. Only tool user should be in work area.

4. Stay alert. Use common sense while operating tool.
5. Keep trigger lock in the OFF position and finger off trigger until ready to

drive staple.

6. Keep work area clean. Cluttered work areas invite injuries.
7. Secure work before using tool. Use both hands to operate tool.
8. Do not touch any metal part of tool when stapling into areas where electri-

cal wiring may be present. These areas include walls, floors, and ceilings.
If staple contacts electrical wire, electric shock may occur.

9. Avoid body contact with grounded objects such as pipes, fences, and metal

posts.

10. Do not force tool. Use tool at rate for which it was designed.
11. Do not overreach. Keep proper footing and balance at all times.
12. Carry tool from one place to another

• with tool unplugged
• with trigger lock in the OFF position
• with finger off the trigger

General
1. Inspect tool before and after each use. Check for any damage that may

affect operator safety or operation of tool. Check for broken or damaged
parts. Do not use tool if damage affects safety or operation.

2. Maintain tool with care.

• Never fire tool when empty of staples. This may damage tool.
• Keep tool clean.
• Keep handles dry, clean, and free of oil and grease.
• Inspect power cord often.
• Never carry tool by power cord.
• Never yank power cord to unplug it.
• Keep power cord away from heat, oil, and sharp edges.
• Inspect extension cords often and replace if damaged.
• Never oil or grease any part of tool.

3. Always store tool

• with staples removed from chamber
• out of children’s reach
• in a high or locked place that is dry

Keep these operating instructions for reference. It is your guide to safe and
proper operation of this tool.

Summary of Contents for HH34392









Reviews: