background image

                                                                                                                                                                                                                     

User and maintenance manual Winch 1111 HL 

 Mod.A 

 

 

1.

 

Glossary 

 

-

 

Intended use: specific and proper use of the winch for which it is designed 

-

 

Improper use: use of the device in a different way from that indicated in the - 
instructions for use specified in this manual 

-

 

Qualified operator: person who has attended specialization and training about the use of 
the winch 

-

 

User: person who uses the winch regularly 

-

 

Maximum working load (MWL): maximum value of the load the winch can bear 

 

 

2.

 

 Symbols 

 

WARNING! 
This denotes the existence of the potential danger, which could cause injury 
or damage if the information or instructions are not followed 
 
 
NOTE! 
This denotes important information concerning the device 

 
 
 

3.

 

Safety information 

 

WARNING! Read this manual carefully and fully understand before using the 
system to avoid personal injury or property damage during system operation. 

 

- This manual is an integral part of the device and provides all the information needed 
for its safe and correct use and for proper maintenance. 
- This manual gives technical information on winch installation and maintenance. 
- This information is destined exclusively for qualified operators. 
- Installation of the winch by personnel who are not experts may cause serious damage 
to users and those in the proximity of the winch. 
- Install and use the winch only as described in the technical information supplied.  
- Improper use can cause severe harms to users, equipment and the boat. 

Summary of Contents for 1111 HL










































Reviews: