background image

3

ENGLISH

05/15/2022

Introduction ���������������������������������������������� 2

About This Manual ���������������������������������������������� 2
Glossary and Symbols ���������������������������������������� 2

Index ������������������������������������������������������ 3 
General Information ������������������������������������ 4

Identification Data on the Device ������������������������ 4
Technical Support Information ��������������������������� 4

Safety Information �������������������������������������� 5

General Advice ���������������������������������������������������� 5
Intended Use������������������������������������������������������� 5
Improper Use ������������������������������������������������������ 5

Winch LokHead 500 KIT�US (INLH500KIT�US) ����� 6

System Description��������������������������������������������� 6

     Parts Description ������������������������������������������� 6

Outline ���������������������������������������������������������������� 7

     Standard Configuration ��������������������������������� 7
     Tripod Use Configuration ������������������������������ 8

MINIMUM BREAKING STRENGHT (MBS) ���������� 9
MAXIMUM WORKING LOAD (MWL) ������������������ 9
Rope Requirements �������������������������������������������� 9
Technical Data ����������������������������������������������������� 9

WARNING:

NOTE:

Lokhead Winch Installation 10

     Mounting Surface  10
     Winch Entry Angle of Lifting Rope  10
     Winch Location  10
     Mounting Template - Plate Adapter  10
     Installation Procedure  11

Positioning the control lever  15
Using The Device - Checking The Device  

Before Use  16
Lifting Load 17
Lowering Load  19
Maintenance  20

     Wash  20
     Maintenance Schedule  20
     Handling  20

Storage  20
Maintenance Schedule  21

Worldwide Limited Warranty ������������������������24

TABLE OF CONTENTS

 WARNING! 

   THIS DENOTES THE EXISTENCE OF THE POTENTIAL 

DANGER, WHICH COULD CAUSE INJURY OR DAMAGE 

IF THE INFORMATION OR INSTRUCTIONS ARE NOT 

FOLLOWED.

NOTE!

 This denotes important 

information concerning the 
device.

Summary of Contents for INLH500KIT.US

























Reviews: