manualshive.com logo in svg

Harley Benton LP-Style, Owner'S Manual

Introducing the Harley Benton LP-Style guitar—the ultimate rock icon. Featuring exceptional craftsmanship and stunning tone, this powerhouse instrument deserves the best care. Ensure a long-lasting partnership with our comprehensive Owner's Manual. Download it for free from 88.208.23.73:8080 and unlock the secrets to maximizing your musical prowess.

Share
Download
background image

www.thomann.de

Harley Benton E-Guitar Kit LP-Style

5

Assembling of tuners

Before­attaching­the­neck­to­the­body,­fit­the­tuning­machine-heads­to­the­headstock­by­inserting­the­thread­

through the pre-drilled holes and setting a washer and bush over it. Screw down the bush onto the thread until 

it­fits­tightly­to­the­touch­and­then­adjust­the­rear­of­the­machine-head­so­that­the­tuning­button­sits­vertically­

above the top edge of the headstock.

Tighten­the­nut­on­the­front­face­of­the­tuner­until­it­is­firm­by­using­a­spanner­of­the­correct­size.­Repeat­this­

for­the­remaining­five­tuners.

Summary of Contents for LP-Style

















Reviews:

No comments

Related manuals for LP-Style

Warwick Jack Bruce Bass Specifications preview
Jack Bruce Bass
Brand: Warwick Pages: 1
Godin Montreal Specification preview
Montreal
Brand: Godin Pages: 3
Warwick FNA Jazzman LTD 2004 Specifications preview
FNA Jazzman LTD 2004
Brand: Warwick Pages: 1
Fender Bullet Deluxe Owner'S Manual preview
Bullet Deluxe
Brand: Fender Pages: 12
Pyle PEAG200 User Manual preview
PEAG200
Brand: Pyle Pages: 10

Brands by name

Popular brands

Load more brands