10
09
Instruction of Using Our Products
Instruction of Using Our Products
SCHEMATIC DIAGRAM OF CONTROL PANEL
RUN CONDITION
1. Water pump surf : AC220V/1.5HP
2. Thermostatic heating : AC220V/1500W
3. Blower : AC220V/300W
4. Bottom lamp : DC12V/1Wx2
5. Ozone : DC12V/6W
OPERATION MANUAL
When any function button works, there is a sound of “ di…”
1.
Press “
press the icon again to stop the controller and all the loads is turned off.
2. LAMP
3. LOCK
When the system is on, press continuouslyand “ ” and “ ” till the cursor is on “
”
；
then press“ ”
，
lamp is turned on
；
press “ ”another time
，
lamp is turned off.
If no operation with the control panel for 3 minutes
，
all the keys will be locked except “LOCK”,
LCD displays “LOCK”.
When the keys were locked
，
press any key for 3 seconds
，
the keys will be unlocked after a
“di…”
，
icon “LOCK” disappear.
power switch
left switch right switch confirmation switch
6.
Loudspeaker : 8Ω/15W
“
” POWER
” for 2 seconds to start the controller,at the same time,the lamp is turned on
；
5. Ozone (FM radio on
，
ozone will be turned off automatically)
When the system is on, press continuously“
、
”
，
when the cursor is on “ ”
6. Blower
When the system is on, press continuously “
” “
”till the cursor moved to“ ”,
and then press “ ”to start the blower
,
the cursor blinks
;
press again, blower is stopped.
7. Water pump surf
The water checking device of this controller protects the water pump from burning out.
When the water level lowers than the setting value, pump stops working.
When the water surf pump function is on, and the system checks the water level lower than
the setting value, water surf pump function stops automatically, at the same time the pump
icon blinks. When any time the system checks the water level achieves the setting value,
the icon stops blink and the pump starts to work.
When the system is on, press“ ” “ ”till the cursor moved to “ ”,while the
water level achieves the setting value ,and then press “ ” to start the pump
，
the
cursor blinks
；
press again, Water pump surf is stopped.
Ozone will be turned off automatically after being started 10 minutes.
Press “ ”again
，
ozone will be turned off.
press“ ”ozone will be started. And LCD symbol will be displayed dynamically.
8. Blue tooth music play (Bluetooth music play cannot be started at the same time with ozone)
8.1 When the system is on, pressing “ ”for 2 Seconds to disconnect the equipment
Password:2288
(previously might have been connected with a Bluetooth device during testing phase of the
production) and enter blue tooth pairing state. LCD displays “PAIR”.
8.2 when the system is on, press constantly “
、
”,to move the cursor to “ ”,
and then press continuously “ ”,till the LCD displays “BT--C”
，
then the blue tooth
music play function is started
；
press again“ ”,till “BT--C” disappears,blue tooth music
play is turned off.
8.3 Blue tooth name is “PROW-BT”. If pairing is not done,LCD blinks “BT--C”; if pairing is
done,LCD displays “BT--C” statically.
8.4 When the blue tooth function is started, press “ ”, until LCD displays “P--N”, by
pressing “ ” to choose next song, by pressing “ ” to choose the last song; by
pressing “ ” for 2 Seconds,to play or pause.
8.5 When the blue tooth music is started,pressing “ ”,until the LCD displays “VOL”,
then it enters volume adjusting state. Press “ ” to increase volume
，
and “ ” to
decrease volume. Volume adjusting range is from 0-20, totally 21.
8.6 When the Bluetooth music play function is ozone will be turned off automatically.
