Harman Kardon AVR 340 Service Manual Download

Page: 14 / 186

MAIN REMOTE CONTROL FUNCTIONS

MAIN REMOTE CONTROL FUNCTIONS 13

Tuning Up/Down:

When the tuner is in use, these

buttons will tune up or down through the selected fre-
quency band. If the

Tuner Mode Button

has

been pressed so that

AUTO

appears in the on-

screen display and

Lower Display Line

, pressing

and holding either of the buttons for three seconds will
cause the tuner to seek the next station with acceptable
signal strength for quality reception. When

MANUAL

appears in the

Lower Display Line

, pressing these

buttons will tune stations in single-step increments. (See
page 41 for more information.)

OSD Button:

Press this button to activate the

On-Screen Display (OSD) system used to set up or
adjust the AVR 340’s parameters.

Dolby Mode Selector:

This button is used to

select from among the available Dolby Surround pro-
cessing modes. Each press of this button will select
one of the Dolby Pro Logic II or IIx, or Dolby Virtual
Speaker modes or Dolby 3 Stereo. When a Dolby
Digital-encoded source is in use, the Dolby Digital
mode may also be selected. When the headphones
are in use, this button selects from among the Dolby
Headphone modes. (See pages 36–37 and 40 for the
available Dolby surround mode options.)

DTS Digital Mode Selector:

When a DTS-

encoded digital source is selected, each press of this
button will scroll through the available DTS modes.
The specific choice of modes will vary depending on
whether the source material contains DTS-ES 6.1
Discrete encoding. When a DTS source is not in use,
this button has no function. (See pages 36 and 40 for
the available DTS digital options.)

Logic 7 Mode Select Button:

Press this button

to select from among the available Logic 7 surround
modes. (See pages 36 and 40 for available Logic 7
options.)

Skip Up/Down Buttons:

These buttons do not

have a direct function with the AVR 340, but when
used with a compatibly programmed CD or DVD
changer they will change to the previous disc in the
changer or carousel.

Transport Controls:

These buttons do not have

any functions for the AVR 340, but they may be
programmed for the forward/reverse play operation
of a wide variety of CD or DVD players, and audio or
video cassette recorders. When the DMP
source is in use, these buttons may be used to oper-
ate some functions on a compatible iPod if it is
docked in The Bridge. See page 42 for more
information on using

When the remote is used to control the AVR, or the
VID2 or VID3 device, by default these buttons are pro-
grammed to operate the DVD player. However, you
may use the Transport Control Punch-Through feature
described on page 50 to program these buttons to
operate another device’s transport controls when the
AVR, VID2 or VID3 has been selected.

Stereo Mode Select Button:

When the button

is pressed so that

SURROUND OFF

appears in

the

Lower Display Line

, with only the

Surr Off

Surround Mode Indicator

lit, the AVR will oper-

ate in a bypass mode with true, fully analog, two-chan-
nel left/right stereo mode with no surround processing
or bass management, unlike other modes where digi-
tal processing is used. When the button is pressed so
that

SURROUND OFF

appears in the

Lower

Display Line

, with both the

DSP

and

Surr Off

Surround Mode Indicators

lit, you may enjoy a

two-channel presentation of the sound along with the
benefits of bass management. Depending on whether
your system is configured for 5.1 or 6.1/7.1 chan-
nels, the next press of the button will cause either

5 CH STEREO

7 CH STEREO

appear, and the stereo signal will be routed to all five
(or seven) speaker channels. (See pages 37 and 40
for more information on stereo playback modes.)

DTS Neo:6 Mode Select:

Press this button to

select a DTS Neo:6 mode. These modes take a two-
channel stereo- or matrix surround-encoded source
and create a full five-, six- or seven-channel sound
field. (See pages 36 and 40 for the DTS Neo:6
options.)

Macro Buttons:

Press these buttons to store or

recall a “Macro”, which is a preprogrammed sequence
of commands stored in the remote. (See page 48 for
more information on storing and recalling macros.)

Disc Skip Button:

This button has no direct

function for the AVR 340 but is most often used to
change to the next disc in a CD or DVD player when
the remote is programmed for that type of device.
(See page 49 for more information on using the
remote with products other than the AVR 340.)

Preset Up/Down:

When the tuner is in use,

press these buttons to scroll through the stations
programmed into the AVR 340’s memory. When
some source devices, such as CD players, VCRs and
cassette decks, are selected using the device

Input

Selectors

, these buttons may function as

Chapter Step or Track Advance.

Clear Button:

Press this button to clear incorrect

entries when using the remote to directly enter a radio
station’s frequency.

Memory Button:

Press this button to enter a radio

station into the AVR 340’s preset memory. First, tune

the desired station, and then press this button. Two
underline indicators will flash at the right side of the

Upper Display Line

, and within five seconds

press the

Numeric Keys

for the preset number

between 01 and 30 that you wish to assign to the
station. (See page 41 for more information.)

Delay/Prev Ch.:

Press this button to begin

the process for setting the delay times used by the
AVR 340 when processing surround sound. After
pressing this button, the delay times are entered by
pressing the

Set Button

and then using the

⁄

Buttons

to select

A/V SYNC

DELAY

or the delay setting for any available chan-

nel. Press the

Set Button

, and then use the

⁄

Buttons

to change the setting. Press the

Set Button

again to complete the process. (See

page 30 for more information.) However, we recom-
mend that you first perform the EzSet/EQ procedure,
as described on pages 25–27.

Speaker Select:

Press this button to begin

the process of configuring the AVR 340’s bass man-
agement system for use with the type of speakers
used in your system. Once the button has been
pressed, use the

⁄

Buttons

to select the

channel you wish to set up. Press the

Set Button

and then use the

⁄

Buttons

to select

the appropriate speaker size. Press the

Set Button

to enter the new setting, and then use the

⁄

Buttons

again to select another channel to

configure. When all adjustments have been completed,
press the

Set Button

twice to exit the settings

and return to normal operation. (See page 28 for
more information.) However, Harman Kardon recom-
mends that you first perform the EzSet/EQ procedure,
as described on pages 25–27.

Multiroom Button:

Press this button to begin

the process of activating the multiroom system, or
changing the source input or volume level for the
remote zone. Press the

⁄¤

Buttons

to scroll

to the on/off, source input or volume level setting, and
then press the

Set Button

to access the desired

setting. Use the

⁄¤

Buttons

to scroll through

the options, and the

Set Button

to select. (See

page 46 for information on the multiroom system.)

Volume Up/Down:

Press these buttons to raise

or lower the system volume. By default, the

Volume

Up/Down Buttons

are programmed at the fac-

tory to control the AVR 340’s volume, no matter which
source device has been selected (except TAPE). You
may reprogram these buttons to control the volume of
another device, such as your TV, using the Volume
Control Punch-Through instructions found on
page 50.

TV/Video Selector:

This button does not have a

direct function on the AVR 340, but when used with a

The

Bridge

The

Bridge

AVR 340 OM 9/13/05 12:45 PM Page 13

AVR340

harman/kardon