Harman Kardon DVD 48 Service Manual Download

Page: 19 / 174

CONNECTIONS

There are different types of audio and video connections used to
connect the DVD 48 to your receiver or processor and video display.
To make it easier to keep them all straight, the Consumer Electronics
Association (CEA

) has established a color-coding standard. Table 1

may be helpful to you as a reference while you set up your system.

Table 1 – Connection Color Guide

Types of Connections

This section will briefly review different types of cables and connections
that you may use to set up your system.

Audio and video signals originate in what are known as “source
devices,” including a DVD/CD player such as the DVD 48.

Separate connections are required for the audio and video portions of
the signal unless an HDMI connection is used (see below). The types of
connections used depend upon what’s available on your receiver, and
for video signals, the capabilities of your video display.

Audio Connections

There are two formats for audio connections: digital and analog. Digital
audio signals are required for listening to sources encoded with digital
surround modes, such as Dolby Digital and DTS. There are two types
of digital audio connections commonly used: coaxial and optical. Either
type of digital audio connection may be used, but never both simultane-
ously. However, it’s okay to make both analog and digital audio connec-
tions at the same time to the same source.

NOTE:

The DVD 48 outputs digital audio signals through the

HDMI connection. If your receiver/processor or video display
is capable of

processing

the audio portion of the HDMI signal,

then you will not need to make a separate digital audio connec-
tion. However, as explained in the Analog Audio section below,
you may still need to make the analog audio connections.

If your receiver/processor is only capable of

switching

HDMI

signals, use HDMI for your video connection only and connect
either the DVD 48’s coaxial or optical digital audio output to
the corresponding input on your receiver.

In addition, SACD audio is not transmitted via HDMI. Use the
2- or 6-Channel Analog Audio Outputs to enjoy your SACD discs.

Digital Audio

Coaxial digital audio jacks are usually color-coded in orange. Although
they look similar to analog jacks, they should not be confused, and you
should not connect coaxial digital audio outputs to analog inputs or
vice versa. See Figure 1.

Figure 1 – Coaxial Digital Audio

Optical digital audio connectors are normally covered by a shutter to
protect them from dust. The shutter opens as the cable is inserted.
See Figure 2.

Figure 2 – Optical Digital Audio

Due to the nature of digital signals as binary bits, they aren’t subject
to signal degradation the way analog signals are. Therefore, the quality
of coaxial and optical digital audio connections should be the same,
although it is important to limit the length of the cable. Whichever type of
connection you choose, Harman Kardon recommends that you always
select the highest quality cables available within your budget.

Analog Audio

Analog connections require two cables, one for the left channel (white)
and one for the right channel (red). See Figure 3. These two cables are
often attached to each other for most of their length. Most devices that
have digital audio jacks also have analog audio jacks. We recommend
that you always connect the DVD 48’s 2-Channel Analog Audio Outputs
to your receiver/processor, or to your TV if you are not using a receiver.
There are four reasons to use analog audio connections, even if you are
using one of the digital audio connections:

1. To make recordings. Most DVDs are protected from digital copying

and only analog copies are permitted. Please make sure to comply
with all copyright laws when making recordings for personal use.

2. In a multiroom system. Many receivers and processors require

sources used in multiroom systems to output analog audio signals.

3. When connecting the DVD 48 directly to a non-HDMI TV. The TV

may not have digital audio inputs.

4. When playing high-resolution 96kHz PCM audio discs. If your receiver

is not capable of processing 96kHz audio, you may need to use the
analog audio connection.

NOTE:

The DVD 48 is capable of downmixing multichannel

materials and outputting a 2-channel downmix. Make sure
to adjust the Analog Output setting in the AUDIO SETUP
menu to Stereo.

Figure 3 – Analog Audio