background image

harman/kardon Incorporated, 250 Crossways Park Dr.  Woodbury, New York  11797  (516) 496-3400

harman/kardon         

Service Bulletin

Service bulletin #  9703   June 1997

This is considered a Major Repair

 To:

All harman/kardon Service Centers

 Models:  FL8300

 Subject:  Dead unit, no display;  Service upgrade

In the event you receive an FL8300 that is dead, and upon inspection R701 is damaged or an otherwise
open circuit, perform the necessary steps listed below:

Due to current surges, early models of the FL8300 could repeatedly damage R701 (either a 1 ohm resistor or
1.5A micro fuse depending on version).  Along with the replacement of R701, the positive lead should be
relocated on C125 to suppress any future current surges.

Additionally, two capacitors, now designated as C907 & C908, (1uf/50v) should be added to the power supply
output pins on regulator IC108 & IC111 on a unit serviced for any reason; these will add stability to help prevent
oscillation.

PROCEDURE:

1)   Replace R701 with micro-fuse H/K # 5508722221, this component is on PCB7.
2)   A PCB trace should be cut on the C125 (2200 uf/25v) positive lead on the main circuit board and an insulated

jumper wire attached from that lead to the junction of D109/110.  Additionally another insulated jumper will
need to replace the trace that was cut. (see drawing)

3)   Add C907 & 908, 1uf/50v , H/K/ # 3479310971, one on each output pin to ground on regulators IC108 and

IC111.  This is most easily accomplished by:

     Soldering one 1uf cap to the jumpers 153 & 197.  Observe polarity; J153 is ground.
     Soldering one 1uf cap to the jumpers 185 & 186.  Observe polarity; J186 is ground.

      Model

Serial number

120V

Serial number

230V

Action

Correction

FL8300

IN0019-72213

and below

NOT REQUIRED

R701 is damaged or

an open circuit

Replace R701,

re-route positive connection

on C125,

Add C907/908

FL8300

IN0019-72214

and above

NOT REQUIRED

Modified by factory

NONE REQUIRED

Summary of Contents for FL 8300





































































Reviews: