background image

TROUBLESHOOTING GUIDE  

15

Troubleshooting Guide

TROUBLE SHOOTING GUIDE

SYMPTOM

No lights on Front Panel

Remote does not appear 
to operate 

Front panel lights, but CD 
does not play

Play indicator lights, but 
no sound is heard

Sound skips or stutters 
during play

Sound is continually distorted

ERROR

lights up continuously 

in the display

CAUSE

• No AC power

• Power Switch turned off
• Weak batteries
• Blocked sensor

• Disc upside down

•Poor connections

• Wrong source connected

• Disc may be damaged
• Surface vibrations 

• Incorrect input

• Various

SOLUTION

• Make certain AC power cord is plugged into 

a live outlet.

• Turn on Power Switch.
• Install fresh batteries, observing polarity indications.
• Remove obstructions from the front panel sensor or connect a

remote sensor to the 

Remote In

jack on the rear panel.

• Reload disc with label side facing up.

• Make certain connections are secure and made

to the correct (e.g.,

CD

) input.

• Select CD source on receiver or preamp.

• Try another disc.
• Isolate the unit from vibration by placing it on a

firm surface or move it further away from speakers.

• Make certain that the analog 

Audio Outputs

of the 

HD750 are connected to a line level audio input, NOT to a
digital audio or phono input.

• Turn the unit off and on again. If the problem persists, turn the

AC power to the HD750 off and on.

Summary of Contents for HD750

















Reviews: