PL0004-01001
1
2
3
4
5
8
9
6
7
44
5
HKTS200SUB Rear-Panel Connections
Subwoofer Level Control:
.
Use this control to adjust the HKTS200SUB’s volume. Turn
clockwise to increase the volume; turn counterclockwise to decrease the volume.
Bass Boost Switch:
1.
Set this switch to
ON
to enhance the HKTS200SUB’s low-frequency
performance. Set this switch to
OFF
for normal low-frequency performance.
Phase Switch:
2.
The
Phase Switch
2
determines whether the HKTS200SUB’s piston-like
action moves in and out in phase with the satellite speakers. If the subwoofer were
to play out of phase with the satellite speakers, the sound waves produced by the
subwoofer could be canceled out, reducing bass performance and sonic impact. This
phenomenon depends in part on the relative placement of all the speakers in the
room. In most cases the
Phase Switch
2
should be left in the
NORMAL
position.
However, it does no harm to experiment, and you can leave the
Phase Switch
2
in
the position that maximizes bass response and impact.
Power On Mode Switch:
3.
When set in the
AUTO
position and when the
Power Switch
7
is set to
ON
, the HKTS200SUB will automatically turn itself on when it receives an
audio signal, and will enter the standby mode once no audio signal has been received
for about 15 minutes. When this switch is set in the
ON
position, the HKTS200SUB
will remain on whether or not it is receiving an audio signal.
An LED on the HKTS200SUB’s top panel indicates whether the subwoofer is in the on
or standby state:
• When the LED is illuminated white, the HKTS200SUB is turned on.
• When the LED is not illuminated, the HKTS200SUB is in standby mode.
When the
Master Power Switch
7
is set to
OFF
, the LED will not be
illuminated, no matter what setting the
Power On Mode Switch
3
is in.
External Trigger Input:
4.
Use the mini-plug of the supplied combination LFE and trigger
cable to connect the
External Trigger Input
to the trigger output of another
compatible component. Whenever a trigger signal between 3 and 30V (AC or DC) is
detected, the HKTS200SUB’s amplifier will turn on. The HKTS200SUB’s amplifier will
turn off after the trigger signal ceases. (This will occur even when the
Power On
Mode Switch
3
is in the
AUTO
position.)
Line-Level LFE In Connector:
5.
Use the LFE (purple) connector of the supplied combination
LFE and trigger cable to connect the
Line-Level LFE In
to the dedicated subwoofer
output of a receiver or preamp/processor. This input bypasses the HKTS200SUB’s
internal crossover circuitry, so it should only be used with a subwoofer output that has
been low-pass filtered. If your receiver or preamp/processor does not have a dedicated
subwoofer output that is low-pass filtered you should use the HKTS200SUB’s
Line-
Level L/R In Connectors
6
instead.
Line-Level L/R In Connectors:
6.
Use these connectors if your receiver or preamp/processor
does not have digital surround sound decoding or a subwoofer output that is low-pass
filtered.
• If your receiver or preamp/processor has a separate subwoofer output, use the LFE
(purple) connector of the supplied combination LFE and trigger cable to connect it to
either one of the HKTS200SUB’s
Line-Level L/R In Connectors.
• If your receiver or preamp/processor does not have a separate subwoofer output,
use two Y-adapters (not supplied). Connect an adapter’s single end to the unit’s
preamp output for that channel. Connect one of the adapter’s dual ends to the main
amp input for that channel, and connect the adapter’s other dual end to one of the
HKTS200SUB’s
Line-Level L/R In Connectors
. Repeat with the other Y-adapter,
preamp channel, main amp input and HKTS200SUB
Line-Level L/R In Connector.
Power Switch:
7.
Set this switch in the
ON
position to turn the HKTS200SUB on. The
subwoofer will then either be on or in standby mode, depending on the setting of the
Power On Mode Switch
3
.
Power Cord (Non-Detachable):
8.
After you have made and verified all subwoofer
and speaker connections described in this manual, plug this cord into an active,
unswitched
electrical outlet for proper operation of the HKTS200SUB. DO NOT plug this
cord into the accessory outlets found in some audio components.
0165CSK - HK HKTS20 and HKTS30 v6.indd 4
08/10/09 13:31:51
