background image

44

5

EN

G

LI

SH

Speaker Placement

NOTE:

 The following speaker placement, mounting and connection instructions are 

identical for the HKTS20 and HKTS30 systems.

Color-Coding System

The HKTS20 and HKTS30 use the channel color-coding system established by the CEA 
to make setting up your home theater speaker system as easy as possible. The HKTS20/
HKTS30 systems include speaker wires with color bands on each end.

Speaker Position

Wire Color Band 

Front Left

White

Front Right

Red

Center

Green

Surround Left

Blue

Surround Right

Gray

Subwoofer

Purple

Placing the Front Speakers

The front speakers should be placed the same 
distance from each other as they are from the  
listening position. They should be placed at about 
the same height from the floor as the listener’s 
ears will be. They also can be angled toward the 
listener.

Left Front 

Speaker

Right Front

Speaker

Placing the Center Speaker

The center speaker should be placed slightly 
behind (farther away from the listener) the front 
left and right speakers. Its center should be no 
more than 2 feet (61cm) above or below the 
tweeters of the front left and right speakers. If you 
have a CRT television, it may be convenient to set 
the center speaker on top of the television set.

0 – 2ft

Center

Speaker

Left Front 

Speaker

Right Front

Speaker

0 - 2 ft  

(0 - 61cm)

Placing the Subwoofer

Since our ears do not hear directional sound 
at the low frequencies where the subwoofer 
operates, it will have good performance from 
just about any location in your room. However, 
the best bass reproduction is likely to be heard 
when the subwoofer is placed in a corner along 
the same wall as the front left and right speakers. 
You can experiment with subwoofer placment 
by temporarily placing it in the listening position 
and playing music with strong bass content. Move 
around to various locations in the room while 
the system is playing and listen until you find the 
location where the bass performance is best. Place 
the subwoofer in that location.

Left Front 

Speaker

Right Front 

Speaker

Subwoofer

Placing the Surround Speakers

Left Surround  

Sound

Right Surround 

Sound

5 - 6 ft

(1.5m - 1.8m)

Left Front 

Speaker

Right Front 

Speaker

Subwoofer

Left Surround  

Sound

Right Surround 

Sound

The two surround speakers should be placed slightly behind the listening position, facing 
each other and, ideally, should be 5–6 feet (1.5m–1.8m) from the floor. An alternate 
location would be on a wall behind the listening position, facing forward. The surround 
speakers should not call attention to themselves while they’re playing.  
Experiment with their placement until you hear a diffuse, ambient sound accompanying 
the program material heard from the front left and right and center speakers.

Mounting Options for Satellite and Center 

Speakers

Shelf Placement

You can place the satellite and center speakers 
on shelves. The satellite speakers have built-in 
bases for shelf placement. You can also remove 
the bases if desired.
To remove a satellite speaker’s base, pull 
it straight off the speaker, as shown in the 
illustration. Applying even pressure to both sides 
of the base will allow it to slide off smoothly. 

Wall-Mounting: Satellite Speakers

IMPORTANT: 

Read the 

Speaker Connections

 

section, on page 7, before wall-mounting the 
satellite speakers. You will need to insert the 
speaker wires through the wall mounts and 
connect the wires to the speakers during the 
process of installing the wall-mounts.

NOTE:

 If you are using your own speaker wire, it must 

be no thicker than the wire supplied with the speakers. Thicker 
wire will prevent the wall-mount bracket from sliding onto the 
speaker. 

Decide on the location for the speaker  

1. 

(

see Speaker Placemen

t, opposite).

Remove the speaker’s base as explained in 

2. 

Shelf Placement,

 above.

Disassemble the wall-mount bracket by sliding the two sections apart, as shown in the 

3. 

illustration.
Attach the wall portion of the wall-mount onto the wall using hardware that is 

4. 

appropriate for the wall’s construction and materials. We recommend first anchoring 
the mount using its keyhole, then attaching it with another anchor through its top 
opening, as shown in the illustration. Note that the satellite speakers weigh 3.3 lb 
(1.5kg). Be sure to use hardware that can support this weight.

Top Opening

Keyhole Opening

Bottom Opening

 

Apply Pressure Evenly

to Both Sides of Base

Lift Base Straight

off Speaker

Pull Sections  

Apart

Center

Speaker

0165CSK - HK HKTS20 and HKTS30 v6.indd   5

08/10/09   13:31:54

Summary of Contents for HKTS 30













Reviews: