background image

PL0004-01001

+

+

+

+

+

PL0004-01001

LEFT

LINE-LEVEL

OUTPUTS

L

R

+ –

+ –

+

+ –

+

+ –

+

RIGHT

SURROUND

FRONT

CENTER

88

9

ENGLISH

Use this installation method for receivers and preamp/processors that do not have a 
dedicated subwoofer output, but do have preamp-level (volume-controlled) line outputs. 
If the receiver or preamp/processor has a dedicated subwoofer output with low-pass 
filtering, see 

Connecting the Subwoofer to a Receiver or Preamp/Processor With a Dedicated 

Subwoofer Output,

 on page 8.

If you’re connecting to a receiver with left and right line outputs that are not connected to 
amplifier inputs, connect the LFE (purple) connector of the supplied combination LFE and 
trigger cable to one of those outputs and to either of the HKTS200SUB’s 

Line-Level L/R 

In Connectors

 

6

. Use a second RCA cable (not supplied) to connect the other receiver or 

preamp line output to the other of the HKTS200SUB’s 

Line-Level L/R In Connectors

 

6

.

If you’re connecting to a receiver or preamp/processor with left and right line outputs 
that are connected to amplifier front left and right inputs, connect the single ends of 
Y-adapters (not supplied) to the receiver’s or processor’s left and right line outputs. 
Connect one of the Y-adapter’s double ends to the HKTS200SUB’s Line-Level

 L/R In 

Connectors

 

6

, and connect the other double end to your amplifier’s front left and right 

inputs. 
Connect each satellite speaker and the center speaker to the corresponding speaker 
terminals on your receiver or amplifier.
In your receiver or preamp/processor’s setup menu, configure it for 

Subwoofer ON

, and set 

the front left, front right, center, and surround speakers to 

Small

.

After you have made and verified all connections, plug the HKTS200SUB’s 

AC Power Cord 

8

 into an active AC outlet.

Connecting the Subwoofer to a Receiver or Preamp/Processor With Line Outputs

Left Front

Receiver

Left 

Surround

Right 

Surround

Subwoofer

Center

Right Front

Front Left

Speaker Cable

(White Bands)

Surround Right

Speaker Cable

(Gray Bands)

Surround Left

Speaker Cable

(Blue Bands)

RCA Cable

(Not Supplied)

(Red and White Ends)

Center

Speaker Cable

(Green Bands)

Front Right

Speaker Cable

(Red Bands)

0176CSK - HK HKTS60BQ-230 v2 press.indd   9

13/11/09   11:24:36

Summary of Contents for HKTS 60













Reviews: