background image

7

SB 10

Speaker Placement

Speaker Placement

Placing the Soundbar on a Table 

If your TV is placed on a table, you can place the soundbar on the table directly in front of 

the TV stand, centered with the TV screen. As long as the surface of the table is flat, the 

soundbar will rest on its rubber bumpers.

If your TV is located in an entertainment or media center, you can mount the soundbar in 

a space directly above or below the TV.

Warning:

 Do NOT place the soundbar directly on top of a TV or at the front of a table or 

cabinet. It could roll forward and injure someone.

Wall-Mounting the Soundbar

If your TV is attached to a wall, you can use the included wall-mount brackets to mount 

the soundbar on the wall directly below the TV screen.

Determine the location for the soundbar on the wall. Make sure that the top 

1. 

of the soundbar will not block your view of the TV screen when it is mounted 

on the wall.
Mark the locations of the soundbar wall-mount bracket holes on the wall. The 

2. 

holes for the left and right brackets are spaced 600mm (23-5/8") apart. The 

top and bottom holes for each bracket are spaced 25mm (1") apart. See the 

illustration below.

NOTE: To ensure that the soundbar will be level, use a carpenter’s level, laser sight or 

other device to help you determine that the two sets of holes are at exactly the same 

height.
Attach  the  two  wall-mount  brackets  to  the  wall  at  the  locations  you  marked,  using 

hardware  that  is  appropriate  for  the  wall’s  construction  and  materials.  Note  that  the 

soundbar weighs 3.67kg (8.1 lb). Be sure to use hardware that can support this weight.

After making all of the connections described in the 

Connections

 section, on page 8, 

attach the soundbar to the brackets by sliding the slots in its rubber bumpers onto the 

brackets’ vertical tabs.

Placing the Subwoofer

Since  our  ears  cannot  locate  the  source  of  sounds  at  the  low  frequencies  that  the 

subwoofer  produces,  it  will  perform  well  from  just  about  any  location  in  your  room. 

However,  you  are  likely  to  hear  the  strongest  bass  reproduction  when  you  place  the 

subwoofer in a corner along the same wall as the soundbar. 

You can determine the best location for the subwoofer by temporarily placing it in the 

listening position and playing music with strong bass content. Move around to various 

locations in the room while the system is playing, and listen until you find the location 

where the bass performance is best. Place the subwoofer in that location.

SB 10 Soundbar

Listening Position

Subwoofer

600mm

25mm

(not to scale)

harman/kardon

SB 10 / 230V Service Manual

Page 4 of 16

Summary of Contents for SB 10/230

















Reviews: