background image

4

Introduction

The Harman Conquest Direct Vent  Gas Stove is a

listed gas-fired direct vent room fireplace tested by
Intertek Testing Services/Warnock Hersey to

 

ANSI

Z21.88-2002,  CSA  2.33-M02    and  CANL/CGA-
2.17-M91.

The  installation  of  the  Conquest  Direct  Vent

Gas Stove must conform with local codes, or in the
absence of local codes, with National Fuel Gas Code,

ANSI Z223.1 — latest edition and CAN 1 B1-149.1

and .2 Installation Code.

Also for use in mobile (manufactured) homes

after home is sited.

Mobile (manufactured) home installations must

adhere to Title 24 CFR, Part 3280, or CSA Z240.4.

CAUTION: This appliance must be vented to

the outside.

Installation and repair of the Conquest Direct

Vent Gas Stove should be done by a qualified ser-
vice person. The appliance should be inspected be-
fore use and at least annually by a qualified service
person. More frequent cleaning may be required due
to  excessive lint  from  carpeting, bedding  material,
etc. It is imperative that control compartments, burn-
ers, and circulating air passageways

 

of the Conquest

be kept clean.

When  operating  your Harman  Conquest  Gas

Stove, respect basic safety standards. Read these in-
structions  carefully  before  you  attempt  to  operate
the stove. Failure to do so may result in damage to
property or personal injury and may void the prod-
uct warranty.

Consult with your local building code agency

and insurance representative before you begin your
installation to ensure compliance with local codes,
including the need for permits and follow-up inspec-
tions.

Several issues must be addressed when select-

ing a suitable location for your Conquest Gas Stove.
Observing required  clearances to  combustible ma-
terials, the proximity to a  safe chimney or venting
system location, and the accessibility of the gas and
electrical supply must all be considered. In addition,
selecting  a  location  that  takes  advantage  of  the
building's natural air flow is also desirable to maxi-
mize the heating effectiveness of the stove. In many
cases, this is a central location within the building.

Due to high temperatures, the Conquest Direct
Vent Gas Stove should be located out of traffic
and away from furniture and draperies.

Children and  adults should be alerted  to the
hazards  of  high  surface  temperatures  and
should  stay  away  to  avoid  burns  or  clothing
ignition.

Young children should be carefully supervised
when  they  are  in  the  s ame  room  as   the
appliance.

Clothing or other flammable materials should
not be placed on or near the appliance.
Surveiller les enfants.  Garder les vetements,
les   meubles ,  les s ence  ou  autres   liquides  a
vapeur inflammables lin de lappareil.

This appliance may be installed in an after-

market  permanently  located  (mobile)  home,
where not prohibited by local codes.

This  appliance  is  only  for  use  with  the

type(s) of gas indicated on the rating plate. This
appliance  is  not  convertible  for  use  with  other
gases, unless a certified kit is used.

Cet  appareil  peut  etre  installe  dans  un

maison  prefabriquee  (mobile)  deja  installee  a
demeure si les reglements locaux le permettent.

Cet  appareil  doit  etre  utilise  uniquement

avec  les  types  de  gas  indiques  sur  la  plaque
signaletique.  Ne pas l utiliser avec d autres gas
sauf si un kitde conversion dertifie est installe.

Any safety screen or  guard removed for servicing
an appliance must be replaced prior to operating
the appliance.

Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

Summary of Contents for Conquest Gas Stove































Reviews: