background image

9

PC 45 Corn/Pellet Stove

Fig. 12

3 ft.

to

combustibles

3 ft.

to

combustibles

Venting

#1  Preferred  method

This method provides excellent venting for nor-

mal  operation  and  allows  the  stove  to  be  installed
closest to the wall. Two inches from the wall is safe;
however, four inches allows better access to remove
the rear panel. The vertical portion of the vent should
be  three to  five  feet high.  This  vertical section  will
provide natural draft in the event of a power failure.

#2  Preferred  method

This method also provides excellent venting for

normal operation but requires the stove to be installed
farther from the wall. The vertical portion of the vent
should be three to five feet high and at least three
inches  from  a  combustible  wall.  This  vertical  sec-
tion will provide natural draft in the event of a power
failure.

If  the  stove  is  installed  below  grade  the  vent

termination should be at least 1 foot above grade.

CAUTION

Keep combustible materials (such as   grass, leaves,
etc.) at least 3 feet away from the flue outlet on the
outside of the building.

Fig. 13

Summary of Contents for PC 45





























Reviews: