Harman Stove Company XXV Installation & Operating Manual Download

Page: 3 / 44

XXV Pellet Stove

3-90-00684R22_04/13

DANGER: Risque d’électrocution. Débrancher

l’appareil avant toute intervention.

Ne remplacer la vitre qu’avec une vitre céramique

5 mm de même qualité disponible auprès de votre

revendeur.

Pour une information plus complète, se reporter à la

notice d’utilisation

Tenir la porte frontale et le couvercle de trémie hermétiquement clos

durant le fonctionnement de l’appareil.

Puissance calorifique émise:

Nominale: 10.5 KW Réduite: 1.8 KW

Concentration CO (à 13 % O2)

à puissance nominale: < 0.02 % à puissance réduite: < 0.04 %

Rendement: à puissance nominale: 84 % à puissance réduite: 73%

DISTANCES DE SECURITE PAR RAPPORT AUX MATERIAUX

COMBUSTIBLES

Entre Mur Arrière et appareil 8 cm

Entre Paroi latérale et appareil 31 cm

Raccord à la Cheminée

13 cm

Installation en angle

Entre murs et apparell

16 cm

Installation en alcôve

Hauter minimale de l’alcôve 150 cm

Parois latérales de l’alcôve

31 cm

Profondeur maximale de l’alcôve 91 cm

PROTECTION DU PLANCHER

Côtés

15 cm

Arrière

0 cm

Avant

15 cm

*mesurer à partir de la surface de la porte en verre.

Utiliser une protection de sol non combustible sous l’appareil qui s’étend

sur les côtés. l’avant et l’arrière du poêle (voir schéma).

ll est recommandé que la protection s’étende jusque sous le conduit

en cas d’installation d’un conduit horizontal ou sous le té en cas de

conduit vertical.

Model: XXV

Residential Space Heating Appliance Fire by Wood Pellets

This pellet burning appliance has been tested and listed for use in Manufactured

Homes in accordance with OAR 814-23-900 through 814-23-909

OMNI-Test Laboratories, Inc.

Report #/Rapport # 135-S14c-6.2

“PREVENT HOUSE FIRES” Install and use only in accordance with the manufacturer’s installation and

operation instructions. Contact local building or fire officials about restrictions and inspection in your area.

WARNING: FOR MANUFACTURED HOMES: Do not install appliance in a sleeping room. An outside

combustion air inlet must be provided. The structural integrity of the manufactured home floor, ceiling and

walls must be maintained.

Refer to manufacture’s instructions and local codes for precautions required for passing chimney through

a combustible wall or ceiling. Inspect and clean exhaust venting system frequently in accordance with

manufacturer’s instructions.

Use a 3” or 4” diameter type “L” or “PL” venting system.

Do not connect this unit to a chimney flue servicing another appliance.

FOR USE WITH PELLETIZED WOOD FUEL OR CORN/PELLET MIXTURE ONLY.

CONSULT MANUFACTURER’S INSTRUCTIONS.

Input Rating Max: 5.7 lb. fuel/hr

Electrical Rating: 240 VAC, 50 Hz, Start 2.6 AMPS, run 2.0 AMPS

U.S. Electrical Rating: 115 VAC, 60Hz, Start 4.2 AMPS, Run 3.6 AMPS

Emissions of CO in combustions:

Nominal Heat Output: .02%, Reduced Heat Output:.04%

Flue Gas Temperature: 224 C

Thermal Output: 10.5kW

Energy Efficiency: Normal: 84%, Reduced: 73%

Fuel Type: Wood Pellets, 5mm diameter, 20mm Lomg

Route power cord away from unit.

DANGER: Risk of electrical shock. Disconnect power supply before servicing.

Replace glass only with 5mm ceramic available from your dealer.

For further instruction refer to owner’s manual.

Keep viewing and ash removal doors tightly closed during operation.

CLEARANCES TO COMBUSTIBLES

Back Wall to Appliance 3”

Side Wall to Appliance 12”
Corner Installation

Walls to Appliance

6.25”

FLOOR PROTECTION

USA

CANADA

Sides (A)*

6”

200MM

Back (B)

0”

200MM

Front (C)*

6”

450MM

*Measured from window opening in the US ONLY.

Use a non-combustible floor protector extending under unit and to the sides, front and back of unit as shown

in Floor Protector Diagram. Measure front distance from the surface of the glass door.

Recommended: Non-combustible floor protection extending beneath the fluepipe when installed with

horizontal venting or under the top vent adapter with vertical installation.

DO NOT REMOVE THIS LABEL

MADE IN THE USA

U.S. ENVIROMENTAL PROTECTION AGENCY

This model is exempt from EPA certification under 40 CFR 60.531 by definition [Wood Heater (A) “Ait-to-Fuel Ratio”].

2012 2013 2014 JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC

Date of Manufacture/Date de Fabrication:

Harman Home Heating - 352 Mountain House Road -Halifax, PA 17032

BARCODE LABEL

AGENCE AMéRICAINE POUR LA PROTECTION DE L’ENVIRONMENT

e modéle est dispensé par EPA certification d’aprè 40 CFR 60.531 par dèfinition [Appareil à bois(A) Ratio air/combustion]

Test to/testé à ASTM E 1509-04, ULC/ORD-C1482-M1990, ULC-S627-00

Tested by Emitech, Apave & BFP Electronique

EN60335-1, EN55014-1, EN 61000-3-2, EN 14785:2005

Test date: February 2004

Room Heater Pellet fuel Burning type (UM) 84-HUD

008

Serial No.

de série:

Test réalisés par OMNI-Test Laboratories, Inc.

Essais Selon les normes 1509-04 de l’ASTM, C1482-M91ULC

Appareil de chauffage à granulés (UM) 84- HUD

NORMES EUROPéENNES:

NF EN 14785 CETIAT – Déc. 2006

AEMC MESURES EN50366 – Déc. 2006

EMITECH, APAVE & BFP Electronique – Fév. 2004

EN55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3

Respecter scrupuleusement les instructions du constructeur pour l’installation

et les consignes de fonctionnement. Respecter les règles de sécurité en

vigueur dans votre région.

AVERTISSEMENT POUR MOBILE HOMES: Ne pas installer dans une

chambre. ll est inpératif de prévoir une prise d’air extérieur. L’intégrité

structurale du plancher, du plafond et des murs doit être strictment préservée.

Se reporter aux instructions du fabricant et aux réglementations spécifiques

locales concernant les précautions requises lors de la traversée d’un mur ou

d’un plafond. Contrôler et nettoyer fréquemment toul le système d’évacuation

des fumées conformément aux recommandations du constructeur.

Utiliser des conduits « spécial granuléls » de diamètre 80 mm ou 100 mm.

Ne pas raccorder ce poêle à un conduit de cheminée déjà utilisé.

FONCTIONNE EXCLUSIVEMENT AVEC DES GRANULES DE BOIS.

SE CONFORMER AUX INSTRUCTIONS D’UTILISATION

Consommation maximale: 2.9 kg/h

Caractéristiques électriques: 240 VC, 50 Hz, Intensité au démarrage 2.6 A,

Intensité fonctionnement normal 2.0 A

Tenir le cordon d’alimentation à l’écart du poéle.

Modèle: XXV

Appareil de chauffage à granulés de bois

Harman XXV Pellet Stove

Label measures: 10.5" high X 5.5"wide

Rev C

P.N. 3-90-00025

This label is located on the back of the unit.

Please copy the Serial Number for future reference.

Serial #:

Summary of Contents for XXV













































Search results

Summary of Contents for XXV

Reviews:

Related manuals for XXV

Brands by name

Popular brands

Harman Stove Company XXV, Installation & Operating Manual

Search results

Summary of Contents for XXV

Reviews:

Related manuals for XXV

Brands by name

Popular brands