6
3-90-08326R35_11/14
See Note 7
1"
Starting First Fire / Igniter Switch to "AuTO"
Make sure the unit is plugged into a 120 VAC, 60 Hz electrical
source. The power light should be the only light lit.
ImPOrTANT:
To avoid unwanted smoke, Be sure there is
no fuel or other combustibles in the ash pan prior to lighting.
Keep all doors closed during operation.
Maintain all seals
and gaskets in good condition.
Use only the burn pot, as supplied in the firebox, to support
or contain the burning fuel. No other form of grate or rack
is permitted.
1.
Turn mode Selector to "OFF".
2.
Fill hopper
with pellets.
3.
Clean burn pot
with scraper, if necessary.
4.
If starting after an empty hopper, turn Feed Adjuster
to "TEST"
(for one 60 second cycle).
This will feed pellets
into the auger tube and also allow you to check the motors
for operation.
NOTE: The auger motor will not operate
with the view door or ash pan door open.
5.
Turn Feed Adjuster to #4.
6.
Flip the Igniter Switch down
into the "AUTO" position.
7.
Turn the Temperature dial
to the desired room
temperature.
8.
Turn the mode Selector
to Room Temperature or Stove
Temperature.
9.
Fill the hopper
with pellets and
remove ashes
as
required.
Automatic Start up
1. Fines are small pieces of broken pellets (sawdust). Fines do
not flow easily and often build up on the hopper funnel bottom
angles. These fines can be pushed into the feeder opening and
then fill the hopper with pellets. As the system works, they will
be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may feed too much
fuel into the burn pot causing excessive smoke on start-up.
3. The firebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door is open.
4. Adjust Feed Rate. If this is your first fire or you are trying different
pellets, set the feed adjuster to #4, Fig. 3. This is a conservative
number and will probably need to be increased. After you know
a feed rate setting that works well, use that setting. Remember,
if your feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of
the burn pot into the ash pan. Then scrape the holed surface
downward into the burn pot. When the stove is ignited these
scrapings will be pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on
"H". Set the Temperature Dial to #7. Allow the unit to burn for
about 30 minutes and check ash on front of burn pot. Fig. 4. If
the ash line is larger than 1", turn the feed adjuster from #4 to
#5. Allow another 30 minutes of burn time and check again. If
, at #6 setting, a 1" or less ash bed is not obtainable, it is not a
problem. The 1" ash bed is only a maximum burn rate and at
most normal settings the ash bed will be larger.
Fig. 3
Fig. 4
dO NOT uSE ChEmICAlS Or FluIdS TO STArT
ThE FIrE. FOr ExAmPlE: NEvEr uSE gASOlINE,
gASOlINE-TYPE lANTErN FuEl, KErOSENE,
ChArCOAl lIghTEr FluId, Or SImIlAr lIQuIdS TO
STArT Or "FrEShEN uP" A FIrE IN ThIS hEATEr.
KEEP All SuCh lIQuIdS wEll AwAY FrOm ThE
hEATEr whIlE IT IS IN uSE.
NOTE: All PACKAgINg & ShIPPINg mATErIAlS
muST bE rEmOvEd FrOm ThE STOvE bEFOrE
OPErATINg.
CAUTION
!
Summary of Contents for Accentra Freestanding Pellet Stove
Page 43: ......
