background image

Clearances

the following clearances to combustibles

 

must be

observed:

heater to left sidewall 

9" (230 mm)

heater to right sidewall 

9" (230 mm)

heater corner to walls 

4" (100 mm)

heater to back wall 

3" (75 mm)

(measured from rear of heater to wall)

heater to alcove ceiling 

18" (460 mm)

Maximum alcove depth 

14" (355 mm)

in  addition  to  the  clearances  mentioned  previously, 

adequate accessibility clearance for servicing and proper 

operation must be maintained.

if this appliance is installed directly on carpeting, vinyl 

tile, or other combustible material other than wood flooring 

the appliance shall be installed on a metal or wood panel ex-

tending at least the full width and depth of the appliance.

Clearance to back wall

3" (75 mm)

IMPORTANT NOTICE

Due to high temperatures, the Clarity Direct Vent 

Gas Heater should be located out of traffic and away 

from furniture and draperies.

Children and adults should be alerted to the haz-

ards of high surface temperatures and should stay 

away to avoid burns or clothing ignition.

Young children should be carefully supervised 

when they are in the same room as the appliance.

Clothing or other flammable materials should 

not be placed on or near the Clarity Direct Vent 

Gas Heater.

18" (460 mm)

Clearance to alcove ceiling.

14" (355 mm)

Maximum alcove depth

Clearance from corner of unit to walls.

INSTALLATION

9" (230 mm)

9" (230 mm)

4"

4"

Air openings into the combustion chamber 

must remain clear at all times.  Also ensure 

adequate accessibility clearances for servicing 

and proper operation.

Summary of Contents for Clarity 929 DV

































Reviews: