background image

 Warranty 

We at 

DigiTech

® are very proud of our products and back-up each one we sell with the following warranty:

2.  DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the 

U.S., to be free from defects in materials and workmanship under normal use and service. This warranty is valid to the 
original purchaser only and is non-transferable.

3.  DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, 

provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up 
to a period of one year. A Return Authorization number may be obtained from DigiTech by telephone. The company shall 
not be liable for any consequential damage as a result of the product’s use in any circuit or assembly.

4.  Proof-of-purchase is considered to be the responsibility of the consumer. A copy of the original purchase receipt must be 

provided for any warranty service.

5.  DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without 

incurring any obligation to install the same on products previously manufactured.

6.  The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered with by anyone 

other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by 
the manufacturer.

7.  The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any 

person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its 
dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes 
beyond their control.

NOTE:

 The information contained in this manual is subject to change at any time without notification. Some information 

contained in this manual may also be inaccurate due to undocumented changes in the product since this version of the manual 
was completed. The information contained in this version of the owner’s manual supersedes all previous versions.

 Service Contact Info 

No returned products will be accepted at the factory without a Return Authorization Number. 

Please refer to the Warranty information, which extends to the first end-user. After expiration of the warranty, a reasonable 
charge will be made for parts, labor, and packing if you choose to use the factory service facility. In all cases, you are 
responsible for transportation charges to the factory. DigiTech will pay return shipping if the unit is still under warranty.

Use the original packing material if it is available. Mark the package with the name of the shipper and with these words in 
red: DELICATE INSTRUMENT, FRAGILE! Insure the package properly. Ship prepaid, not collect. Do not ship parcel post.

1.  Please register online at within ten days of purchase to validate this warranty. This warranty is valid only in the United 

States.

If you require technical support, contact DigiTech Technical Support. Be prepared to accurately describe the problem. Know 

the serial number of your device - this is printed on a sticker attached to the chassis. If you have not already taken the time 
to register your product, please do so now at

Before you return a product to the factory for service, we recommend you refer to the manual. Make sure you have correctly 
followed installation steps and operation procedures. For further technical assistance or service, please visit our support 

page at. If you need to return a product to the factory for service, you MUST first contact Technical Support to obtain a 
Return Authorization Number. 

Summary of Contents for DigiTech JamMan Vocal XT
















Reviews: