background image

2

 The User Interface & Connectors 

The User Interface

1.  LOOP LEVEL Knob 

This knob controls the output level of the 

loop� The 12 o’ clock position represents 

unity gain�

2.  MIC LEVEL Control 

Adjust this control to set the input gain 

for your microphone� This control also 

doubles as a multi-color signal and clip 

indicator� It will light green when signal is 

present, orange when approaching the clip 

point and red when clipping occurs� For 

optimal signal to noise performance, set 

this control so it lights green and orange 

regularly during normal performance and 

only lights red rarely on the loudest vocal 

signals� 

3.  Footswitch 

This Footswitch is used to perform all 

JamMan Vocal XT functions (i�e�, record, 

play, overdub, undo/redo, stop, and clear 

loop)�

1

6

2

1

3

4 5

2

3

4

4.  Status LEDs 

These LEDs indicate the status of the pedal as described in the below table� 

 

LED

Status

REC

Loop is being recorded.

PLAY

Loop is playing.

DUB

Overdub is being recorded.

DUB

Overdub is being undone/redone.

REC

DUB

PLAY

Pedal is in standby 

(recording/playback stopped).

LED

Status

REC

Loop is being cleared 

(footswitch held).

Slave armed for record 

(connected as slave via JamSync).

REC

DUB

PLAY

Slave synchronization established via 

JamSync.

 

Summary of Contents for DigiTech JamMan Vocal XT
















Reviews: